User's Manual

ManualsBrandsRolling Code ManualsElectronicsRemote Control

TX USA

MANUAL TX USA

ATTENTION: THIS REMOTE WORKS IN TWO DIFFERENT WAYS:

1. ENTERING DIRECTLY THE RECEIVER

2. CLONING

ATTENTION: IN TX USA (MULTICLONER) YOU CAN PUT A DIFFERENT BRAND AND FREQUENCY IN EACH

BUTTON (CHANNEL) ONLY IN CLONE MODE.

ENTERING DIRECTLY THE RECEIVER MODE

PROGRAMMING INSTRUCTIONS

1. Locate the selector switch in the back of the remote. Pry up the cover to expose the selector

switch and the hidden button, see image below.

2. Set your selector switch of 8 DIPs switch with the desired brand. See Table 1 and image below.

3. Head for your receiver, in case it has DIPs switch, this defines the code of this specific receiver, please

select this same combination from the receiver in the transmitter TX USA, both must match, otherwise the

communication between them will not work.

In case your receiver doesn’t have this DIP selector, this section must be ignored, it is not neccessary.

4. The remote is ready to be used, press any button (from 1 to 3) please refer to your receiver’s user

manual.

Note: To programme BFT and MUTANCODE it will be necessary to press the hidden button (beside the switches) before

pressing one ordinary button (button 1 to 3).

Image to locate battery and DIP switches for selecting the brand.

TECHNICAL FEATURES

ü Model TX USA

ü 2 BATTERIES 2032 (3V)

ü Frequencies 315 - 390 MHz

ü 3 Channels

ü Special Chip

SPECIFIC RECEIVER’S CODE

HIDDEN BUTTON BRAND SELECTOR

Summary of content (7 pages)

PAGE 1
TX USA MANUAL TX USA TECHNICAL FEATURES ü Model TX USA ü 2 BATTERIES 2032 (3V) ü Frequencies 315 - 390 MHz ü 3 Channels ü Special Chip ATTENTION: THIS REMOTE WORKS IN TWO DIFFERENT WAYS: 1. ENTERING DIRECTLY THE RECEIVER 2. CLONING ATTENTION: IN TX USA (MULTICLONER) YOU CAN PUT A DIFFERENT BRAND AND FREQUENCY IN EACH BUTTON (CHANNEL) ONLY IN CLONE MODE. ENTERING DIRECTLY THE RECEIVER MODE PROGRAMMING INSTRUCTIONS 1. Locate the selector switch in the back of the remote.
PAGE 2
TX USA Table 1: Entering directly the receiver.
PAGE 3
TX USA 1 2 3 4 5 6 7 8 LiftMaster 8 Fixed Code 1 2 3 4 5 6 7 9 Code 2 3 4 5 6 7 315 MHZ 8 Fixed 1 BILLIONCODE 8 10 LiftMaster BILLIONCODE 390 MHZ Liftmaster Encrypted Chamberlain Code Lobas 315 MHZ 1 2 3 4 5 6 7 8 11 Liftmaster Encrypted Chamberlain Code Lobas 390 MHZ 1 2 3 4 5 6 7 8 12 1 2 3 4 5 6 7 14 2 3 4 5 6 7 SOMMER code 315 FM MHZ Rolling MCT-3 Linear code 318 MHZ 8 13 1 Rolling 8 Fixed Code Marantec 315 MHZ
PAGE 4
TX USA 1 2 3 4 5 6 7 8 15 1 2 3 4 5 6 7 Rolling Genie Code 315MHz 8 Encrypted 16 Code 1 2 3 4 5 6 7 17 Code 2 3 4 5 6 7 2 3 4 5 6 390MHz Liftmaster BILLIONCODE 315MHz 8 18 1 LOBAS 8 Fixed 1 Liftmaster 7 Rolling Genie Code 315MHz Mode A 8 19 Rolling Genie Code 315MHz Code select by position 1 to 9 on DIP12 1 2 3 4 5 6 7 8 20 1 21 2 3 4 5 6 7 Fixed GUARDIAN Code 303MHz 8 Code select DIP MULTI CODE by position 1 Code 3
PAGE 5
TX USA 1 2 3 4 5 6 7 8 Code select 22 DIP LINEAR2 by position 1 Code 310MHz to 8 on DIP12 1 2 3 4 5 6 7 8 Code select 23 DIP DIGI CODE by position 1 Code 310MHz to 10 on DIP12 1 2 3 4 5 6 7 8 Encrypted Code Liftmaster LOBAS 315MHz CLONE MODE PROGRAMMING INSTRUCTIONS 1. Locate the selector switch in the back of the remote. Pry up the cover to expose the selector switch and the hidden button, see the image above. 2. Select the DIP position brand.
PAGE 6
TX USA Num DIP SWITCHES 1 2 3 4 5 6 R/F 7 Brand Compatible Comments SCAN MODE 8 Universal 1 Original Fixed Fixed Code Code 300 - 390MHz Scan ANY fixed code remote with frequency from 300 to 390 MHz. 1 2 3 4 5 6 7 SCAN MODE 8 2 V2 V2 300 - 390 MHz Scan V2 remotes that work with frequencies from 300 to 390 MHz. 1 3 2 3 4 5 6 7 8 HCS Universal Rolling Code 300-390MHz SCAN MODE Scan ANY Rolling Code that works with frequencies from 300 to 390 MHz.
PAGE 7
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.