Setup Guide Most of the figures in this document depict the LEC-330. Read this first. This describes the setup tasks and important conditions about the installation location that must be met in order to enable use of this machine.
Thank you very much for purchasing this product. To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely and store it in a safe location. Unauthorized copying or transferral of this manual, in whole or in part, is prohibited. The contents of this document and the specifications of this product are subject to change without notice.
Contents Contents.........................................................................................................1 To Ensure Safe Use........................................................................................2 Pour utiliser en toute sécurité......................................................................9 Setup Guide.........................................................................................................17 1. Installation Environment...............................
To Ensure Safe Use Improper handling or operation of this machine may result in injury or damage to property. Points which must be observed to prevent such injury or damage are described as follows. About WARNING and WARNING CAUTION Notices Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.
To Ensure Safe Use Incorrect operation may cause injury WARNING Be sure to follow the operation procedures described in this documentation. Never allow anyone unfamiliar with the usage or handling of the machine to touch it. Incorrect usage or handling may lead to an accident. Keep children away from the machine. The machine includes areas and components that pose a hazard to children and may result in injury, blindness, choking, or other serious accident.
To Ensure Safe Use Danger of electrical short, shock, electrocution, or fire WARNING Connect to an electrical outlet that complies with this machine's ratings (for voltage, frequency, and current). Incorrect voltage or insufficient current may cause fire or electrical shock. Ratings Never use out of doors or in any location where exposure to water or high humidity may occur. Never touch with wet hands. Doing so may result in fire or electrical shock. Never allow any foreign object to get inside.
To Ensure Safe Use Important notes about the power cord, plug, and electrical outlet Never place any object on top or subject to damage. Never allow to get wet. Never bend or twist with undue force. Never make hot. Never pull with undue force. Dust may cause fire. Never bundle, bind, or roll up.
To Ensure Safe Use Ink, cleaning fluid, and discharged fluid are flammable and toxic WARNING Keep open flame away from the work area. Ink and discharged fluid are flammable. Never store ink, cleaning fluid, or discharged fluid in any of the following locations. Any location exposed to open flame Any location where high temperature may occur Near bleach or any other such oxidizing agent or explosive material Any location within the reach of children Fire may be a danger.
To Ensure Safe Use This machine weighs 210 kg (463 lb.). Media weighs 20 kg (44 lb.). WARNING WARNING Install the machine in a location that is level, stable, and able to bear the weight of the machine. The total weight of the machine may reach 210 kg (463 lb.) or more. Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse. Unloading and emplacement are operations that must be performed by 6 persons or more.
To Ensure Safe Use Warning Labels Warning labels are affixed to make areas of danger immediately clear. The meanings of these labels are as follows. Be sure to heed their warnings. Also, never remove the labels or allow them to become obscured. Flammable Ink and discharged fluid are flammable. Keep away from open flame. Ink Is Toxic Ink and discharged fluid are toxic. Avoid contact with the body. Use only in a well-ventilated area.
Pour utiliser en toute sécurité La manipulation ou l'utilisation inadéquates de cet appareil peuvent causer des blessures ou des dommages matériels. Les précautions à prendre pour prévenir les blessures ou les dommages sont décrites ci-dessous. Avis sur les avertissements ATTENTION Utilisé pour avertir l'utilisateur d'un risque de décès ou de blessure grave en cas de mauvaise utilisation de l'appareil.
Pour utiliser en toute sécurité L'utilisation incorrecte peut causer des blessures ATTENTION S'assurer de suivre les procédures d'utilisation décrites dans la documentation. Ne jamais permettre à quiconque ne connaît pas le fonctionnement ou la manutention de l’appareil de le toucher. L'utilisation ou la manutention incorrectes peuvent causer un accident. Garder les enfants loin de l'appareil.
Pour utiliser en toute sécurité PRUDENCE Ne jamais grimper ni s'appuyer sur la machine. La machine n'est pas conçue pour supporter le poids d'une personne. Grimper ou s'appuyer sur la machine peut déplacer des éléments et causer un faux pas ou une chute, ce qui causerait des blessures. PRUDENCE Attention : outil de coupe. Cet appareil contient un outil interne. Pour éviter les blessures, manipuler l'outil avec soin.
Pour utiliser en toute sécurité Risque de décharge ou de choc électrique, d'électrocution ou d'incendie ATTENTION Manipuler le câble d'alimentation, la fiche et la prise électrique correctement et avec soin. Ne jamais utiliser un article endommagé, car cela pourrait causer un incendie ou un choc électrique. Si une rallonge ou une bande d'alimentation électrique sont utilisées, s'assurer qu'elles correspondent aux caractéristiques de l'appareil (tension, fréquence et courant).
Pour utiliser en toute sécurité Remarques importantes à propos du câble d'alimentation, de la fiche et de la prise électrique Ne jamais déposer aucun objet sur le câble, sur la fiche ou sur la prise car cela risque de les endommager. Ne jamais laisser l'eau toucher le câble, la fiche ou la prise. Ne jamais plier ni tordre le câble avec une force excessive. Ne jamais chauffer le câble, la fiche ou la prise. Ne jamais tirer sur le câble ou la fiche avec une force excessive.
Pour utiliser en toute sécurité L'encre, les liquides nettoyants et les liquides usées sont inflammables et toxiques ATTENTION ATTENTION Ne pas approcher une flamme nue de l'espace de travail. L'encre et les liquides usés sont inflammables.
Pour utiliser en toute sécurité Le poids de cet appareil est de 210 kg (463 lb.) Le poids du support est de 20 kg (44 lb.) ATTENTION Installer l'appareil à un endroit stable et plat et capable de supporter son poids. Le poids total de l'appareil peut être d'au moins 210 kg (463 lb.). Installer l'appareil à un endroit inapproprié peut provoquer un accident grave comme le renversement, la chute ou l'écrasement. Le déchargement et la mise en place doivent être faits par au moins six personnes.
Pour utiliser en toute sécurité Vignettes d'avertissement Des vignettes d'avertissement sont apposées pour qu'il soit facile de repérer les zones dangereuses. La signification des vignettes est donnée ci-dessous. Respecter les avertissements. Ne jamais retirer les vignettes et ne pas les laisser s'encrasser. Inflammable L'encre et les liquides usés sont inflammables. Les garder loin de toute flamme nue. L'encre est toxique L'encre et les liquides usés sont toxiques. Éviter tout contact avec le corps.
Setup Guide 17
1. Installation Environment Deciding On an Installation Site Install in a quiet, stable location offering good operating conditions. An unsuitable location can cause accident, fire, faulty operation, or breakdown. 18 WARNING Install the machine in a location that is level, stable, and able to bear the weight of the machine. The total weight of the machine may reach 210 kg (463 lb.) or more. Installation in an unsuitable location may cause a major accident, including tip over, fall, or collapse.
1. Installation Environment Unsuitable Installation Sites Following locations can cause malfunction or poor printing quality.
1. Installation Environment Installation Space The space shown in the figure is required in order to use this machine. 3200mm (126 in.) 2200mm (86.6 in.) Unit Space 900mm (35.4 in.) 2200mm (86.6 in.) Work Space Air Ventilation This machine emits a small amount of volatile compounds during printing and for some time after printing, which may cause irritation of your eyes, nose, and throat. To use this machine, make sure to install ventilating equipment for adequate ventilation. ? P.
2. Included Items The following items are packed together with the unit. Make sure they are all present and accounted for. Stay Dancer roller Stand leg (left) Rail slider Stand leg (right) Paper tube Shafts Power cord Arm / Arm retaining screw Drain bottle Media flanges Stoppers Drain-bottle stand Short media clamps Long media clamps * Bolts Washers Blade Blade holder/Pin Replacement blades for separating knife * The long media clamps are installed on the machine.
2. Included Items SOL INK cleaning cartridges User's Manual Hexagonal wrench (5 mm) Setup guide (This document) Cleaning kit Cleaning fluid Cleaning sticks Replacement wipers Tweezers Head-unit tool Software RIP White and Gloss Ink Guide Cartridge-slot label (Included only with LEC-330.
3. Assembling and Installing Step 1: Assemble the Stand CAUTION Unpacking and installation must be carried out by six or more persons. Otherwise the machine or the stand may fall, resulting in injury. 1. Attach the stand legs to the stay. Place the stay on the accessories box. Stay Use this box Place at the center of the stay. Accessories box Attach the left and right stand legs to the stay. Loosely tighten the locations shown in the figure.
3. Assembling and Installing Tighten the remaining bolts. Fully tighten all bolts to secure the stay and stand legs completely. After assembling, lock all casters and remove the accessories box. 4 places 4 places Bolts Hexagonal wrench Hexagonal wrench Bolts Lock Caster 2. Attach the rail slider and the arm. Attach the arm to the rail slider, securing it secure with the arm retaining screw. Rail slider Arm Arm retaining screw 24 Orient this side toward the rear.
3. Assembling and Installing Mount the rail slider on the stand legs and secure it in place with the bolts. Line up the tab with the slot in the rail slider and, working with the right stand leg first, secure in place. Bottom surface of the rail slider Cap-unit tool Slot Tab Line up the tab with the slot. 3. Attach the dancer roller. Remove the packing material at the location shown in the figure.
3. Assembling and Installing Attach the dancer roller. Secure in place using bolts, working on the right side first. Dancer roller Line up with the bolt hole and secure in place. Line up with the bolt hole and secure in place. 4. Attach the shafts and engage the brake. Fit the stoppers onto the shafts. Fit two stoppers onto each shaft. Orient so that this side faces outward.
3. Assembling and Installing Place the shafts on the stand and engage the brake. Peel off the tape. Flip down toward the outer side. Place the shafts on the stand. Engage the brake. 5. Attach the paper tube. Pull the dancer roller back toward you.
3. Assembling and Installing Mount the paper tube and secure the arm in place. First, fit the paper tube securely onto the end cap on the same side as the right stand leg. Next, press the end cap on the same side as the arm into the paper tube and securely fit the end cap into the paper tube. Finally, secure the arm in place using the arm retaining screw. Tighten the screw while pressing down from above. End cap End cap Arm Paper tube Fit onto this securely. Fit onto this securely.
3. Assembling and Installing Step 2: Mount the Machine CAUTION Unpacking and installation must be carried out by six or more persons. Otherwise the machine or the stand may fall, resulting in injury. Procedure Place the machine on the stand. Bottom surface of the printer Printer Align with the fittings on the stand. Secure the machine to the stand.
3. Assembling and Installing Step 3: Install the Drain Bottle Procedure Remove the drain-tube cover and attach the bottle stand. Attach the drain-tube cover to the underside of the machine for storage. Remove the drain-tube cover. Secure the bottle stand in place. Using the bolts that held the drain-tube cover in place, secure the bottle stand in place.
3. Assembling and Installing Remove the lid from the drain bottle. Carefully store the lid and inner cap so that they will not be misplaced. Lid Inner cap Drain bottle From the back of the machine, attach the drain bottle. At the location shown in the figure, secure in place the part you removed in step. Fasten using the bolt provided, which is attached to the underside of the machine.
3. Assembling and Installing Step 4: Remove the Packing Materials Packing materials are attached to the machine to protect it from vibration during transportation. When installation is complete, remove them. Remove all packing materials. Any that remain may cause faulty operation or breakdown when the power is switched on. Store the packing materials carefully, because they are needed again when transporting the machine for relocation or the like. Packing material Remove 32 Peel off the tape.
3. Assembling and Installing You can attach the removed packing materials at the location shown in the figure for storage. Bottom surface of the main unit Packing material Align with the two tabs and secure in place.
3. Assembling and Installing Step 5: Attach the Rear Cover Procedure Secure the left and right rear-cover stays in place with the screws. Use a commercially available Phillips screwdriver. Screws Screws Rear-cover stay (right) Rear-cover stay (left) Back of the machine Engage the rear cover on the left and right rear-cover stays. Engage. Engage.
3. Assembling and Installing Step 6: Attach the Media Guide Procedure Move the dancer roller toward the rear. Dancer roller Secure the media guide in place with screws. Remove the screws from the machine, and secure the media guide in place with them. Use a commercially available screwdriver.
4. Connecting the Cables Connecting the Cable of the Take-up Unit Peel off the tape. Pass the take-up unit cable through at the locations shown in the figure, and connect it.
4. Connecting the Cables Connecting the Power Cord and the Network Cable WARNING Connect to electrical outlet that complies with this machine's ratings (for voltage, frequency, and current). Incorrect voltage or insufficient current may cause fire or electrical shock. WARNING Connect to ground. This can prevent fire or electrical shock due to current leakage in the event of malfunction. WARNING Perform this task with all power switches left switched off.
5. Installing the Ink Cartridges(LEC-300A) Filling with Ink for the First Time When installing ink cartridges for the first time, clean the print heads with the cleaning solution, and then fill with ink of each color. This operation requires four SOL INK cleaning cartridges. * For SOL INK cartridges and ink cartridges, be sure to use new ones. * Never, under any circumstances, use anything other than the specified type of ink or cleaning fluid.
5. Installing the Ink Cartridges (LEC-300A) At the locations shown in the figure, affix the cartridge-slot labels matching the selected ink mode. Affix here. Back of the machine Ink cartridge cover Ink type Cartridgeslot labels to affix Ink type ECO-UV CMYKGlW (Cyan, magenta, yellow, and black ECO-UV ink cartridges, one gloss ink cartridge, and one white ink cartridge are used.) None ECO-UVS CMYKWW (Cyan, magenta, yellow, and black ECO-UVS ink cartridges and two white ink cartridges are used.
5. Installing the Ink Cartridges (LEC-300A) Installing the Ink Cartridges Be sure to follow the on-screen instructions for insertion and removal. Arrow Slot number Insert in the direction shown in the figure. Insert and remove slowly, one at a time. Insert firmly, as far as it will go. During cleaning, you insert and remove cartridges several times. The on-screen messages indicate which to insert and remove, and when to insert and remove them.
5. Installing the Ink Cartridges (LEC-300A) Switch on the main power switch. Main power switch Hold down and press the sub power switch. MENU LANGUAGE JAPANESE Use Press LENGTH UNIT mm mm Use to select the unit of measurement you want (for length). TEMP. UNIT C Use to select the unit of measurement you want (for temperature). Press . C . to select the language you want. 2. Clean the print heads using the SOL INK cleaning cartridge. Press and select the ink type.
5. Installing the Ink Cartridges (LEC-300A) INSTALL DRAIN BOTTLE Make sure the drain bottle is installed. Press . SET CL-LIQUID 1234 Insert the SOL INK cleaning cartridges into slots 1, 2, 3, and 4. FILLING INK... >> REMOVE CL-LIQUID 1234 Pull out the SOL INK cleaning cartridges. Insert the SOL INK cleaning cartridges you pulled out into slots 5 and 6. SET CL-LIQUID 56 FILLING INK... >>>> REMOVE CL-LIQUID 56 Pull out the SOL INK cleaning cartridges. FILLING INK...
5. Installing the Ink Cartridges (LEC-300A) 3. Insert the ink cartridges for the respective colors. Before you insert the ink cartridge for each color, gently shake the cartridge. SET CARTRIDGE 123456 Insert the ink cartridge for each color. FILLING INK... >>>>>>>>>> Insert into the slot of the matching color. Close the ink cartridge cover. CHECK DRAIN BOTTLE Make sure the drain bottle is installed. Press .
5. Installing the Ink Cartridges (LEC-300A) SETUP SHEET ROLL When this screen appears, filling with ink is finished. Be Sure to Keep the Ink Cartridge Cover Closed at All Times. The ink cartridge cover prevents the ink cartridges from being exposed to direct sunlight or strong illumination. If the ink cartridges are exposed to them, the ink inside the cartridges will become hardened, and it may cause the printer to malfunction.
6. Installing the Ink Cartridges (LEC-330) Ink Mode In the case of LEC-330, you need to select the ink mode in accordance with the ink type. P.47, "Selecting the Ink Mode" ECO-UV gloss/gloss mode This mode uses cyan, magenta, yellow, and black ECO-UV ink cartridges and two gloss ink cartridges. ECO-UV white/white mode This mode uses cyan, magenta, yellow, and black ECO-UV ink cartridges and two white ink cartridges.
6. Installing the Ink Cartridges (LEC-330) At the locations shown in the figure, affix the cartridge-slot labels matching the selected ink mode. Affix here.
6. Installing the Ink Cartridges (LEC-330) Selecting the Ink Mode Be sure to make the selection of the ink mode when switching on the power for the first time. Procedure Close the front cover. If the main power switch is on, then switch it off. Hold down and ,switch on the main power switch. When a message appears on the display screen, release the operationpanel buttons. SET INK MODE GLOSS INK and ,switch on the main power switch.
6. Installing the Ink Cartridges (LEC-330) Hold down until the message appears. Main power switch ECO-UV gloss/gloss mode ECO-UV white/white mode Display screen Press at the same time Press at the same time ECO-UV gloss/white mode ECO-UVS ink mode Press at the same time Press at the same time Press . The sub power switches off automatically. This completes selection of the ink mode. Go on to the next step, "Installing the Ink Cartridges.
6. Installing the Ink Cartridges (LEC-330) Installing the Ink Cartridges Be sure to follow the on-screen instructions for insertion and removal. Arrow Insert in the direction shown in the figure. Insert and remove slowly, one at a time. Insert firmly, as far as it will go. Slot number During cleaning, you insert and remove cartridges several times. The on-screen messages indicate which to insert and remove, and when to insert and remove them.
6. Installing the Ink Cartridges (LEC-330) 2. Clean the print heads using the SOL INK cleaning cartridge. SELECT INK TYPE ECO‑UV CMYKGlGl ECO-UV gloss/gloss mode SELECT INK TYPE ECO‑UV CMYKWW ECO-UV white/white mode SELECT INK TYPE ECO‑UV CMYKGlW Check the selected ink mode. Press . Switch off the sub power. Again carry out the procedure on page 47, "Selecting the Ink Mode.
6. Installing the Ink Cartridges (LEC-330) REMOVE CL-LIQUID 56 Pull out the SOL INK cleaning cartridges. FILLING INK... >>>>>>>> CHECK DRAIN BOTTLE When this screen appears, cleaning is finished. Make sure the drain bottle is installed, and press . 3. Insert the ink cartridges for the respective colors. Before you insert the ink cartridge for each color, gently shake the cartridge. SET CARTRIDGE 123456 Insert the ink cartridge for each color. FILLING INK...
6. Installing the Ink Cartridges (LEC-330) Close the ink cartridge cover. CHECK SETUP SHEET ROLL DRAIN BOTTLE Make sure the drain bottle is installed. Press . When this screen appears, filling with ink is finished. Be Sure to Keep the Ink Cartridge Cover Closed at All Times. The ink cartridge cover prevents the ink cartridges from being exposed to direct sunlight or strong illumination.
7. Installing the Blade CAUTION Be sure to perform operations as specified by these instructions, and never touch any area not specified in the instructions. Sudden movement of the machine may cause injury. CAUTION Never touch the tip of the blade with your fingers. Doing so may result in injury, and the cutting performance of the blade will be impaired. 1. Insert a blade into the blade holder. Insert the pin. Leave the pin inserted. Pin Cap Blade holder Insert the blade.
7. Installing the Blade Open the front cover. FINISHED? When this screen appears, preparation is completed. 3. Install the blade holder. Loosen the screw shown in the figure. Screw Support the screw from below and insert the blade holder. If installed without supporting the screw in this way, cutting quality may become poor. Screw Support it from below. Insert until the collar is flush with the surface. Tighten the screw. Tug the blade holder upward to make sure it does not come loose.
8. Network Settings Introduction This machine has a built-in print server as a network interface. When you use the print server, you can send printing data to the machine from anywhere on the network. TCP/IP is used as the protocol. Make sure the machine is connected to the network by an Ethernet cable. The network settings on the machine must be made manually, using the operation panel.
8. Network Settings For Windows 2000: From the [Start] menu, click [Settings], then click [Network and Dial-up Connections]. Double-click the [Local Area Connections] icon. Click [Properties]. Click [Allow] when the [User Account Control] dialog box appears. The [Local Area Connection Properties] dialog box appears. Select [Internet Protocol Version 4 (TCP/ IPv4)] (Windows 7/Vista) or [Internet Protocol (TCP/IP) (Windows XP/2000), then click [Properties].
8. Network Settings In the [Local Area Connection Properties] dialog box, click [OK], then in the [Local Area Connection Status] dialog box, click [Close]. Step 2: Make the Network Settings on the Printer Important The addresses used in this section are merely example settings. For detailed information about the settings, consult your network administrator. 1. Set the IP address. MENU SYSTEM INFO. Press Press . several times. SYSTEM INFO. NETWORK Press Press . . IP ADDRESS 000 . 000 .
8. Network Settings 2. Set the subnet mask. NETWORK SUBNET MASK Press . SUBNET MASK 000 . 000 . 000 . 000 Press twice. SUBNET MASK 255 . 000 . 000 . 000 Use to select the address number. [Subnet mask] : 255.255.255.000 Note: For the subnet mask, make the setting the same value as the one used by the computer. Here, "255.255.255.000" is entered by way of example. SUBNET MASK 255 . 000 . 000 . 000 SUBNET MASK 255 . 255 . 255 . 000 W 736 mm SETUP SHEET ROLL Press .
8. Network Settings GATEWAY ADDR. 255 . 255 . 000 . 000 Press GATEWAY ADDR. 255 . 255 . 255 . 255 Repeat and to set the gateway address numbers. When you've finished making the setting, press . W 736 mm SETUP SHEET ROLL Press Press . . to go back to the original screen. Step 3: Make the Port Settings for the Software RIP Make the settings for the software RIP. For the output destination, use the setting for the IP address made on the printer.
9. Installation of Ventilating Equipment Ventilating Equipment ? P. 20, “Air Ventilation.” In preparing ventilating devices, please note the following points. You will be required to use the ventilating devices recommended by Roland DG Corporation. For the details of the recommended products, contact your authorized Roland DG Corp. dealer. You will need a hose to connect the ventilating equipment and this machine.
9. Installation of Ventilating Equipment Attach the hose to the connection port on the unit. Insert all the way.
62
63
64
R2-120802
