Owner`s manual
73
Effects List
This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
fig.MFX-24
This is a flanger in which the flanger pitch changes in steps. The speed
at which the pitch changes can also be specified in terms of a note-
value of a specified tempo.
fig.MFX-25
Uses a six-phase chorus (six layers of chorused sound) to give richness
and spatial spread to the sound.
fig.MFX-26
24: FLANGER
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000 Hz
Center frequency when using the
filter to cut a specific frequency
range
Pre Delay 0.0–100 msec
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Rate # 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback # -98–+98%
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Balance # D100:0W–D0:100W
Volume balance between the direct
sound (D) and the flanger sound (W)
Level 0–127 Output Level
25: STEP FLANGER
R in
R out
L in
L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Step Flanger
Step Flanger
Parameter Value Explanation
Filter Type OFF, LPF, HPF
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Cutoff Freq 200–8000 Hz
Center frequency when using the
filter to cut a specific frequency
range
Pre Delay 0.0–100 msec
Adjusts the delay time from when
the direct sound begins until the
flanger sound is heard.
Rate # 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Phase 0–180 deg Spatial spread of the sound
Feedback # -98–+98%
Adjusts the proportion of the
flanger sound that is fed back into
the effect. Negative (-) settings will
invert the phase.
Step Rate # 0.10–20.00 Hz, note Rate (period) of pitch change
Low Gain -15–+15 dB Gain of the low range
High Gain -15–+15 dB Gain of the high range
Balance # D100:0W–D0:100W
Volume balance between the
direct sound (D) and the flanger
sound (W)
Level 0–127 Output Level
26: HEXA-CHORUS
Parameter Value Explanation
Pre Delay 0.0–100 msec
Adjusts the delay time from the
direct sound until the chorus sound
is heard.
Rate # 0.05–10.00 Hz, note Frequency of modulation
Depth 0–127 Depth of modulation
Pre Delay
Deviation
0–20
Adjusts the differences in Pre Delay
between each chorus sound.
Depth
Deviation
-20–+20
Adjusts the difference in modulation
depth between each chorus sound.
Pan Deviation 0–20
Adjusts the difference in stereo
location between each chorus
sound.
0: All chorus sounds will be in the
center.
20: Each chorus sound will be
spaced at 60 degree intervals
relative to the center.
Balance # D100:0W–D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Level 0–127 Output Level
Balance W
Balance W
L in
R in
L out
R out
Hexa Chorus
Balance D
Balance D