Owner's manual
EXR-5/EXR-3 MIDI Implementation
11
●
Patch parameters
If you like to send messages to the 16 Parts relative to Arranger and Keyboard, you have to use the address 50 xx xx (if “MIDI TxRx”= “ALL”; use “40 xx xx” if “MIDI TxRx”= “STL”).
If you like to send messages to the 16 Parts relative to Songs, you have to use the address 40 xx xx (if “MIDI TxRx”= “ALL” or “SNG”).
❍
Patch common parameters
The parameters common to all Parts in each module are called Patch Common parameters.
M-FX EFFECT LIST
Address(H)
Size(H) Data(H) Parameter Description Default Value (H) Description
40 00 00 00 00 04 0018~07E8 MASTER TUNE -100.0~+100.0 [cents] 00 04 00 00 0 [cents]
40 00 01# Use nibblized data.
40 00 02#
40 00 03#
• Refer to section “4. Supplementary material”, About the Tuning (page 19).
40 00 04 00 00 01 00~7F MASTER VOLUME 0~127 7F 127
(= F0 7F 7F 04 01 00 vv F7)
40 00 05 00 00 01 28~58 MASTER KEY-SHIFT -24~+24 [semitones] 40 0 [semitones]
40 00 06 00 00 01 01~7F MASTER PAN -63 (LEFT)~+63 (RIGHT) 40 0 (CENTER)
40 00 7F 00 00 01 00 MODE SET 00 = GS Reset
(Rx. only)
40 01 00 00 00 10 20~7F PATCH NAME 16 ASCII Characters
40 01 : #
40 01 0F#
40 01 30 00 00 01 00~07 REVERB MACRO 00: Room 1 04 Hall 2
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
40 01 31 00 00 01 00~07 REVERB CHARACTER 0~7 04 4
40 01 32 00 00 01 00~07 REVERB PRE-LPF 0~7 00 0
40 01 33 00 00 01 00~7F REVERB LEVEL 0~127 40 64
40 01 34 00 00 01 00~7F REVERB TIME 0~127 40 64
40 01 35 00 00 01 00~7F REVERB DELAY FEEDBACK 0~127 00 0
40 01 37 00 00 01 00~7F REVERB PREDELAY TIME 0~127 [ms] 00 0
• REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set
to their most suitable value.
• REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
Address(H)
Size(H) Data(H) Parameter Description Default Value (H) Description
40 01 38 00 00 01 00~07 CHORUS MACRO 00: Chorus 1 02 Chorus 3
01: Chorus 2
02: Chorus 3
03: Chorus 4
04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay(FB)
40 01 39 00 00 01 00~07 CHORUS PRE-LPF 0~7 00 0
40 01 3A 00 00 01 00~7F CHORUS LEVEL 0~127 40 64
40 01 3B 00 00 01 00~7F CHORUS FEEDBACK 0~127 08 8
40 01 3C 00 00 01 00~7F CHORUS DELAY 0~127 50 80
40 01 3D 00 00 01 00~7F CHORUS RATE 0~127 03 3
40 01 3E 00 00 01 00~7F CHORUS DEPTH 0~127 13 19
40 01 3F 00 00 01 00~7F CHORUS SEND LEVEL TO
REVERB
0~127 00 0
• CHORUS MACRO is a macro parameter that allows global setting of chorus parameters. When you select the chorus type with CHORUS MACRO, each Chorus parameter will be
set to their most suitable value.
Address(H)
Size(H) Data(H) Parameter Description Default Value (H) Description
40 4x 22 00 00 01 00, 01 PART EFX ASSIGN 00:BYPASS 00 BYPASS
01:EFX
Address(H) Size(H) Data(H) Parameter Description Default Value (H) Description
40 03 17 00 00 01 00~7F EFX SEND LEVEL TO REVERB 0~127 28 40
• EFX TYPE is a macro parameter which sets various Insertion Effect parameters as a group. When you use EFX TYPE to select an Insertion Effect type, each effect parameter will
be set to the most suitable value.
00 Thru
Effect Type F0 41 10 42 12 40 03 00 00 00 3D F7 Thru
01 Enhancer
Effect Type
Sens = 127
Mix = 64
F0 41 10 42 12 40 03 00 01 02 3A F7
F0 41 10 42 12 40 03 03 7F 3B F7
F0 41 10 42 12 40 03 04 40 79 F7
Enhancer
Value Hex. 00~7F
Value Hex. 00~7F
02 Overdrv1
Effect Type
Amp Type Small
Drive = 48
Pan = 64
F0 41 10 42 12 40 03 00 01 10 2C F7
F0 41 10 42 12 40 03 04 00 39 F7
F0 41 10 42 12 40 03 03 30 0A F7
F0 41 10 42 12 40 03 15 40 68 F7
Overdrive
Small
Value Hex. 00~7F
Value Hex. 00~7F
03 Overdrv2
Effect Type
Amp Type Bltln
Drive = 48
Pan = 64
F0 41 10 42 12 40 03 00 01 10 2C F7
F0 41 10 42 12 40 03 04 01 38 F7
F0 41 10 42 12 40 03 03 30 0A F7
F0 41 10 42 12 40 03 15 40 68 F7
Overdrive
Bltln (Default)
Value Hex. 00~7F
Value Hex. 00~7F