Owner`s manual

ManualsBrandsRoland ManualsComputer equipmentDM-20

Summary of additional functions in version 1.20

FireWire card support

By installing an IF-FW/DM FireWire interface card

(sold separately), it is now possible to transfer audio

data between your computer and a DM-3200. An

IF-FW/DW card can only be installed into Slot 1.

Surround monitor card support

Integrated surround monitoring can be added to the

DM-3200 by installing an IF-SM/DM surround moni-

tor card (sold separately). An IF-SM/DM card can be

installed into either Slot 1 or 2.

Naming the mixer

DM-3200 Ver1.20 allows you to set and edit mixer

names.

Remote operation through MMC

Now you can remotely operate external transports

from a DM-3200 using the MMC (MIDI Machine

Control) protocol.

MIDI control

External MIDI devices can be controlled from the

DM-3200 using MIDI Control Change and Program

Change Messages using the new external controllers:

MIDI fader, MIDI controller, and MIDI mixer.

Assigning parameters to rotary encoders

DM-3200 now allows you to assign which parameters

are controlled from the rotary encoders.

Cascade connection

A cascade connection can be made between two

DM-3200 units.

GPI functionality

DM-3200 can now remotely control external devices

using a GPI signal output.

Expanded dynamic automation function

The dynamic automation function of the DM-3200 can

now capture buss assignments, effect parameters, and

image parameters.

Table of Contents

Summary of additional functions in version 1.20 .................................1

FireWire card support ..............................................................................

Surround monitor card suppo

rt ..............................................................2

Naming the mixer ....................................................................................2

Remote operation through MMC ...........................................................

MIDI control .............................................................................................

Connection ..........................................................................................3

Setting devices for MIDI control ........................................................

Selecting devices for MIDI control ..........................................

Selecting control types for the devices ...................................

Setting up individual devices .................................................. 4

MIDI controllers ..................................................................................

MIDI fader ...........................................................................................4

MIDI mixer ...........................................................................................5

Changing the assignment ........................................................5

Assigning parameters to rotary encoders ..............................................

Cascade connection .................................................................................6

Cascade connection overview ........................................................... 6

Master/slave setting ...........................................................................6

Making a cascade connection ............................................................7

Settings and Operations that can be interlocked ............................7

Settings that can be interlocked .............................................7

Operations that can be interlocked ........................................7

GPI functionality ......................................................................................8

Making connections ........................................................................... 8

Setting the GPI ....................................................................................8

GPI CONFIG section ...................................................................8

TIME EVENT section ..................................................................9

Editing the GPI EVENT LIST ...................................................... 9

Expanded dynamic automation function ............................................10

Additional dynamic automation parameters .................................10

Additional parameters that are re-played as Initial Status ...........

Settings prohibited to change during automation re-play ...........

TASCAM DM-3200 Ver 1.20 1

DM-3200 Ver1.20 Supplemental Manual

Summary of content (12 pages)

PAGE 1
» DM-3200 Ver1.20 Supplemental Manual Table of Contents Summary of additional functions in version 1.20 .................................1 FireWire card support ..............................................................................2 Surround monitor card support ..............................................................2 Naming the mixer ....................................................................................2 Remote operation through MMC ...........................................
PAGE 2
DM-3200 Ver1.20 Supplemental Manual FireWire card support By installing an IF-FW/DM FireWire interface card (sold separately) into Slot 1 of the DM-3200 Ver1.20, you can transfer audio data between your computer and the DM-3200. An IF-FW/DM inserted into Slot 2 will not function. Figure 1 is an example of the panel display when an IF-FW/DM card is installed in Slot 1. For more details, please refer to the IF-FW/DM documentation.
PAGE 3
DM-3200 Ver1.20 Supplemental Manual Remote operation through MMC DM-3200 Ver1.20 allows you to remotely operate the transport functions of external devices through MMC (MIDI Machine Control). Device control is carried out through the MIDI IN/OUT port. The USB port cannot be used for this purpose. Selection of external devices for transport control is done on the REMOTE/MACHINE CTRL screen. For details, please see “Selecting devices for transport control” on page 93 of the DM-3200 Owner’s Manual.
PAGE 4
DM-3200 Ver1.20 Supplemental Manual Continued from the previous page ªSelecting control types for the devices Each of the columns on the EXTERNAL CONTROL LIST will display the following when an MIDI device is added to the list. STATE: A one-way arrow ® is displayed, representing an open-loop device. DEVICE: The name of the device is displayed together with the number of channels available for transmitting control signals. MIDI control has 16 channels.
PAGE 5
DM-3200 Ver1.20 Supplemental Manual Continued from the previous page MIDI Volume (Control Change 7) is frequently used. This allows the DM-3200 to remotely control the sound volume of up to 16 external MIDI devices. This is only possible when Layer Status is set to REMOTE and the MIDI FADER screen is currently showing or was the last EXT.CTRL screen displayed. When a Control Change message is received from an external MIDI device, the value will be reﬂected in the fader of DM-3200.
PAGE 6
DM-3200 Ver1.20 Supplemental Manual Assigning parameters to rotary encoders You can assign parameters to the rotary encoders using the four encoder mode keys (please refer to the “Encoders” section on page 20 in the Owner’s Manual). In the previous versions of DM-3200, parameters were pre-assigned as indicated next to each of the encoder mode keys. In Version 1.20 you can select which parameter is to be controlled by which of the encoder mode keys.
PAGE 7
DM-3200 Ver1.20 Supplemental Manual Continued from the previous page Making a cascade connection This section explains how to make a cascade connection between two DM-3200s that are running Version 1.20. 1 Using the TASCAM cascade cable (PW-1000CS – sold separately), connect the CASCADE ports of the two DM-3200. WARNING Only use the special TASCAM cascade cable. Use of any other type of cable may result in damage to the equipment.
PAGE 8
DM-3200 Ver1.20 Supplemental Manual GPI functionality DM-3200 Ver1.20 supports GPI functionality. This allows you to send 8 output signals from the GPI port (D sub 9-pin connector) on the rear panel, and control external devices from the DM-3200. The right side of the screen allows you to set which event is to happen when the GPI is controlled by the timecode. The DM-3200 allows you to give different trigger settings to each of the GPI ports for GPI signal output.
PAGE 9
DM-3200 Ver1.
PAGE 10
DM-3200 Ver1.20 Supplemental Manual Expanded dynamic automation function Additional dynamic automation parameters The following parameters can now be captured and re-played by the dynamic automation function of DM-3200 (please see “Automated Controls” on the page 4 of the DM-3200 Automation Guide). • Image Image parameter of the linked channel (please see “Pan and balance settings” on page 71 of the DM-3200 Owner’s Manual).
PAGE 11
Memo TASCAM DM-3200 Ver 1.
PAGE 12
TEAC CORPORATION Phone: +81-422-52-5082 D00908410A 3-7-3, Nakacho, Musashino-shi, Tokyo, 180-8550 Japan Printed in China