User`s manual

ManualsBrandsRoland ManualsComputer equipmentCAMM-2 PNC-2300

Part 2

Index

<A>

Accessories ......................................................................... 1

Application software ........................................................ 17

Arrow keys ......................................................................... 3

“AUTO” (COMMAND selection) .............................. 6, 25

“AUTO” (I/O selection) ............................................ 17, 26

Adhesive sheet ................................................................ 1, 7

<B>

Baud rate....................................................................... 6, 25

“BAUDRATE” ............................................................. 6, 25

“BUFFER EMPTY” ......................................................... 33

<C>

CAMM-GL I .............................................................. 17, 34

CAMM-GL I Programmer’s Manual ............................... 34

Centronics ................................................................. 5, 6, 42

Character cutter ............................................................ 1, 41

Chip cleaning .............................................................. 18, 27

Clamps ............................................................................ 1, 7

Cleaning............................................................................ 27

- Cleaning the after operation .................................... 18, 27

- Cleaning the main unit .................................................. 27

Clear ........................................................................... 21, 24

“CLEAR” ................................................................... 21, 24

Collet .............................................................................. 1, 8

“COMMAND” ................................................................. 26

Connection.......................................................................... 5

- Computer connection ...................................................... 5

- Power cord connection .................................................... 5

- Vacuum cleaner connection........................................... 11

Connection parameters ....................................................... 6

“CONTINUE” (pause state) ............................................. 23

Coordinate value............................................................... 24

Cover .................................................................................. 2

“COVER OPEN”.............................................................. 33

Cutter .................................................................. 1, 8, 15, 41

Cutter holder ................................................................... 1, 8

- Replacing the cutter holder and collet............................. 8

Cutter down key ................................................................. 3

Cutter down position ........................................................ 16

Cutter up key ...................................................................... 3

Cutter up position ............................................................. 16

Cutting area ...................................................................... 19

Cutting condition ...................................................... 13—15

Cutting-in amount........................................... 10, 13, 14, 15

<D>

“DATA” ........................................................................ 6, 25

Data bits ........................................................................ 6, 25

Data buffer ........................................................................ 21

Depth regulator nose................................................... 2, 8, 9

Device control instructions ............................................... 37

Display menus ............................................ 24—26, 39—40

Display menus flowchart .......................................... 39—40

Double-sided tape ............................................................... 8

<E>

EMERGENCY STOP switch ............................................. 3

“EMERGENCY STOP” ................................................... 33

ENTER/PAUSE key ........................................................... 3

Error messages.................................................................. 32

External output connector............................................. 2, 43

<F>

Feed rate ............................................................... 13, 15, 22

Flowchart (display menus) ....................................... 39—40

<H>

“HANDSHAKE”.......................................................... 6, 25

Head.................................................................................... 2

Hexagonal screw driver ...................................... 1, 9, 10, 18

“HOME” ........................................................................... 24

Home position .................................................................. 12

<I>

“I/O” ....................................................................... 6, 24, 25

Installation .......................................................................... 4

Instruction system....................................................... 17, 26

Interface specifications ..................................................... 42

Interface type ................................................................ 5, 25

<L>

Labels ................................................................................. v

Language .......................................................................... 20

Liquid-crystal display ......................................................... 3

- Loading a cutter............................................................... 8

- Loading a workpiece ................................................... 7, 8

Lock-use pin ....................................................................... 5

<M>

Maintenance ............................................................. 27—29

Maximum cutting area................................................ 19, 42

MENU key.......................................................................... 3

mode1 ............................................................................... 34

mode2 ............................................................................... 35

Motor brushes ............................................................... 1, 27

<O>

Options ............................................................................. 41

Origin.......................................................................... 11, 12

“OTHERS” ................................................................. 24, 26

“OVER_AREA” ............................................................... 26

<P>

“PARA” ............................................................................ 25

Parallel cable ...................................................................... 5

Parallel connection ......................................................... 5, 6

Parallel connector ........................................................... 2, 5

“PARITY” .................................................................... 6, 25

Parity check .................................................................. 6, 25

Part names .......................................................................... 2

“PAUSE” .................................................................... 22, 23

Power connector ............................................................. 2, 5

Power cord ...................................................................... 1, 5

Power switch .................................................................. 2, 5