User Manual

ManualsBrandsRoland ManualsDigital Pianos with MobileDP990RF PE Digital Piano - DIGITAL PIANO

Table Of Contents

Introduction
- About the Manual
  - Conventions in this Manual
- Main Features
Contents
USING THE UNIT SAFELY
Important Notes
Names of Things and What They Do
- Front Panel
- Rear Panel
- Bottom Panel
Before You Play
- Getting Ready to Play
- Turning the Power On/Off
- Adjusting the Sound’s Volume and Brilliance
- About the Pedals
- Listening through Headphones
  - Using the Headphone Hook
- Using External Memory
  - Connecting USB Memory (sold separately)
  - Installing the Floppy Disk Drive (sold separately)
- Using CD
  - Connecting a CD Drive (sold separately)
  - Installing the CD Drive Holder (sold separately)
Listening to Demo Songs
- Listening to the Tone Demo Songs
  - Listening to the Piano Sound Demo Songs
Performing
- Performing with a Variety of Sounds
- Adjusting the Keyboard Sensitivity (Key Touch)
- Adding Spatial Depth to the Sound (3D Sound Control)
- Adding Liveliness to the Sound (Dynamics Sound Control)
- Adding Reverberation to Sounds (Reverb Effect)
  - Changing the Depth of Reverb Effect
- Changing the Key of the Keyboard (Key Transpose)
- Dividing the Keyboard for Two-person Performance (Twin Piano)
  - Changing the Way in Which the Sound is Heard (Twin Piano Mode)
- Performing With Two Layered Tones (Dual Play)
  - Changing the Tone Variations
  - Changing the Volume Balance for Dual Play
- Performing with Different Tones in the Left and Right Sides of the Keyboard (Split Play)
  - Switching Tone Groups and Tone Variations
  - Changing the Keyboard’s Split Point
- Performing with the Metronome
- Sounding a Count to Keep your Timing Accurate
Playing Back Songs
- Listening to Songs
- Playing Back All Songs Continuously (All Song Play)
- Listening to Each Part Separately
  - Determining the Volume of a Muted Part
- Changing the Song Playback Volume
  - Adjusting the Volume of the Audio Files and Music CDs
- Changing the Tempo of a Song
  - Playing Back at a Fixed Tempo (Tempo Mute)
- Changing the Key of the Song Playback (Playback Transpose)
- Minimizing the Center Sounds in the Playback (Center Cancel)
Recording
- Recording Your Keyboard Performance
- Recording Your Performance Separately for Each Hand
- Recording Your Playing Along with a Song
- Erasing Recorded Performances
Saving Your Performance
- Initializing the Memory
- Saving the Songs
- Deleting a Song
Various Settings
- Basic Operation in Function Mode
  - Changing How Grand Space is Applied (3D Mode)
- Keyboard Settings
- Pedal Settings
  - Changing How the Damper Pedal Effects Is Applied (Damper Pedal Part)
  - Changing How the Pedals Work (Center/Left Pedal Function)
- Tuning Settings
- Sound-related Settings
- Metronome Settings
  - Changing the Sound of the Metronome (Metronome Sound)
- Count-down Setting
- Song Playback Settings
  - Switching the Part that Will be Muted When You Press the [Accomp] Button (Accomp Track)
- MIDI Settings
- Other Settings
- Remembering the Settings (Memory Backup)
- Restoring the Settings to the Factory Condition (Factory Reset)
- Disabling the Buttons (Panel Lock)
Connecting to Other Devices
- Connecting to Audio Equipment
  - Connecting Speakers to the DP-990 and Outputting Sounds
  - Playing Sounds of an Audio Device through the DP-990
- Connecting to MIDI Devices
  - Connecting a MIDI Sequencer to the DP-990
  - Producing Sounds from a MIDI Sound Module by Playing the DP-990
- Connecting a Computer
Troubleshooting
Error Messages
Tone List
Internal Song List
Parameters Stored in Memory Backup
Music Files That the DP-990 Can Use
MIDI Implementation Chart
Main Specifications
Index

Various Settings

You can change the sound that’s played by the metronome.

The metronome will sound when you enter the setting screen.

Hold down the [Brilliance] button and press

the [3D] button.

The display will indicate “Fnc” and you’ll be in Function

mode.

Press the [Metronome] button.

The display will indicate “Mt.S” and then the value of

the setting will appear.

Use the [-] [+] buttons to change the setting.

A “count-down” is when a count is sounded at the end of the

song’s introduction (before you begin playing the keyboard). If

you will be playing along with the song, sounding a count will

help you match the timing of your playing with the song.

Hold down the [Brilliance] button and press

the [3D] button.

The display will indicate “Fnc” and you’ll be in Function mode.

Hold down the [Tempo] button and use the [-]

[+] buttons to make the display indicate “Ctd.”

When you take your finger off the button, the display

will indicate the value of the setting.

Use the [-] [+] buttons to change the setting.

You can select the sound that will be used to play the count-

down.

Hold down the [Brilliance] button and press

the [3D] button.

The display will indicate “Fnc” and you’ll be in Function mode.

Hold down the [Tempo] button and use the [-]

[+] buttons to make the display indicate

“Cd.S.”

When you take your finger off the button, the display

will indicate the value of the setting.

Use the [-] [+] buttons to change the setting.

Metronome Settings

Changing the Sound of the Metronome

(Metronome Sound)

Sound

(Click), (Electronic),

(Voice: japanese), (Voice: English),

(Animal), (Wood Block),

(Triangle & Castanets), (Hand Claps)

Count-down Setting

Sounding a Count Before the Melody

Begins (Countdown)

Setting

Explanation

A count is sounded

A count is not sounded

Selecting the Count-down Sound

(Countdown Sound)

Sound

(Voice: English), (Voice: Japanese)

DP-990_e.book 73 ページ２００９年２月１７日　火曜日　午前８時３０分