User Manual
Table Of Contents
- Introduction
- Contents
- USING THE UNIT SAFELY
- Important Notes
- Names of Things and What They Do
- Before You Play
- Listening to Demo Songs
- Performing
- Performing with a Variety of Sounds
- Adjusting the Keyboard Sensitivity (Key Touch)
- Adding Spatial Depth to the Sound (3D Sound Control)
- Adding Liveliness to the Sound (Dynamics Sound Control)
- Adding Reverberation to Sounds (Reverb Effect)
- Changing the Key of the Keyboard (Key Transpose)
- Dividing the Keyboard for Two-person Performance (Twin Piano)
- Performing With Two Layered Tones (Dual Play)
- Performing with Different Tones in the Left and Right Sides of the Keyboard (Split Play)
- Performing with the Metronome
- Sounding a Count to Keep your Timing Accurate
- Playing Back Songs
- Recording
- Saving Your Performance
- Various Settings
- Basic Operation in Function Mode
- Keyboard Settings
- Pedal Settings
- Tuning Settings
- Sound-related Settings
- Metronome Settings
- Count-down Setting
- Song Playback Settings
- MIDI Settings
- Other Settings
- Remembering the Settings (Memory Backup)
- Restoring the Settings to the Factory Condition (Factory Reset)
- Disabling the Buttons (Panel Lock)
- Connecting to Other Devices
- Troubleshooting
- Error Messages
- Tone List
- Internal Song List
- Parameters Stored in Memory Backup
- Music Files That the DP-990 Can Use
- MIDI Implementation Chart
- Main Specifications
- Index
69
Various Settings
When you press the damper pedal during Dual performance
or Split performance, the damper pedal effect is normally
applied to both tones, but you can also select the tone to
which the effect is to be applied.
1.
Hold down the [Brilliance] button and press
the [3D] button.
The display will indicate “Fnc” and you’ll be in Function
mode.
2.
Press the [Twin Piano] button.
The display will indicate “dPr” and then the value of the
setting will appear.
If the display does not indicate “dPr,” hold down the
[Twin Piano] button and press the [-] button several
times.
3.
Use the [-] [+] buttons to change the setting.
When you turn on the power, the left pedal functions as the
soft pedal, and the center pedal functions as the sostenuto
pedal (p. 21).
You can change the function of the pedal to a variety of other
operations.
1.
Hold down the [Brilliance] button and press
the [3D] button.
The display will indicate “Fnc” and you’ll be in Function
mode.
2.
Hold down the [Twin Piano] button and use the
[-] [+] buttons to select the pedal whose
function you want to change.
: Center Pedal
: Left Pedal
3.
Use the [-] [+] buttons to change the setting.
Pedal Settings
Changing How the Damper Pedal
Effects Is Applied (Damper Pedal Part)
Setting
Explanation
All enabled
Applied only to the Tone 1 (in dual mode)/Right-
hand Tone (in split mode)
Applied only to the Tone 2 (in dual mode)/Left-hand
Tone (in split mode)
Changing How the Pedals Work
(Center/Left Pedal Function)
Setting
Explanation
Sostenuto
Sets function to sostenuto pedal.
(Selectable only for the center pedal)
Soft
Sets function to soft pedal.
(Selectable only for the left pedal)
Effects Switch
Effects can be switched on/off by pressing the pedal.
When effect type is rotary, you can control the
slow/fast of spinning.
* The most appropriate type of effect is specified
for each sound.
Play/Stop
The pedal will have the same function as the
[ ] button.
Layer
Pressing the pedal will layer on Tone 2, used for
Dual performance.
* The Layer function can be applied only when
using Dual play.
Octave
Pressing the pedal will layer on a sound one
octave higher.
* The Octave function cannot be applied while
using Twin Piano, Dual play, or Split play.
DP-990_e.book 69 ページ ２００９年２月１７日 火曜日 午前８時３０分