nano mobile USER MANUAL EziTrak® Nano Mobile v1.0.
Table of Contents 1.0 General Information.........................................................................................................4 Signal Strength & Availability...........................................................................................5 Surveillance Laws............................................................................................................5 Installation Health Check.........................................................................................
7.0 Detailed Command Set..................................................................................................20 ACCELEROMETER and MAN DOWN..........................................................................20 AT COMMANDS............................................................................................................21 BLACKBOX....................................................................................................................22 BUZZER.............................
1.0 General Information Congratulations on selecting the EziTrak® Nano Mobile Personnel Monitoring System. This system is one of the most sophisticated systems of it’s kind on the market today. As such, the information contained in this user manual is very comprehensive to allow you to use the full functions of this system as required. It is recommended that this document be read thoroughly to avoid false alarms or not being informed of alarm or emergency events.
Signal Strength & Availability Full functionality is best achieved in areas where both good GSM Network Service and GPS satellite broadcast signal can be received. Wide, open outdoor areas are ideal for the GPS satellite receiver. GPS receivers can suffer interference from transmitting devices which may cause dropouts in GPS coverage but this is generally uncommon and more likely in large commercial centres. The EziTrak® Nano Mobile must have BOTH GSM and GPS services available to function.
For a first time setup with a generic SIM card: This will prevent the unit attempting to connect to the internet BEFORE the unit is setup; 1. Insert the SIM Card. 2. Turn the Unit ON. 3. After a couple of minutes send the following commands to the unit via SMS text, OR via the EziTrak® Nano Mobile USB Utility software. 1234.GPRS.APN.telstra.internet for Telstra 1234.GPRS.APN.vfinternet.au for Vodafone 1234.GPRS.APN.internet for Optus 1234.GPRS.APN.busintpub for Optus business 1234.GPRS.APN.
GPRS Registration Your EziTrak® Nano Mobile is capable of connecting to the INTERNET using the GPRS Network over GSM. This simply means that you can Monitor your Personnel over the Internet. To use the Internet based service, you must … 1. Register your details with the EziTrak® GPRS Server. 2. Pay the Yearly Registration Fee. 3. Ensure your EziTrak® Nano Mobile SIM card is GPRS Enabled.
2.0 Unit Description 2 5 3 4 6 1 Kit Contents 1. Unit 2. Windscreen Cradle 3. Belt Cradle 4. Mini USB Cable 5. Wall USB Power Charger 6. Car USB Power Charger 7. USB Stick with Manuals & Software (not shown) The EziTrak® Nano Mobile unit has an ON/OFF Switch, USB Charger Port, SIM Card Slot, LED Viewing Window and a red Panic/Marker Button.The EziTrak® Nano Mobile unit has 2 cradle options including a Belt Clip and a Vehicle Windscreen Mount. 8 Rojone Pty. Limited – EziTrak® Nano A.B.
Unit Features and Functions GPS TRACKING Map position update rates from Once Per Second (1Hz) to Once Per 255 Seconds (4.25 Minutes) programmable in 1 Second Steps. Note: Updates less than 10 seconds only on special request. STANDALONE MODE The unit can run in standalone mode where the unit is not connected to the server via GPRS. The unit can be configured to automatically send its position periodically or by request from a phone call or SMS.
STREET ADDRESS LOCATION The unit can provide standalone location information to ANY mobile phone. To locate a unit simply use a mobile phone to dial the phone number of any tracking unit and then hang up. The unit will return an SMS to the incoming caller containing the current Street Address and Status of the unit. BLACKBOX RECORDER The unit can record GPS and Event information to an internal Black Box in case there is no network signal present.
LED INDICATOR The unit has an LED display window which indicates that the unit is functioning correctly as well as the state of battery charging. When the unit is functioning correctly the blue LED will flash. CONNECTION STRATEGY The Unit will try to stay connected to the Internet at all times. If it becomes disconnected it will attempt to reconnect every 120 seconds. BUT if GPRS.MOVING CONNECT.ON has been programmed, then the unit will NOT use the Timer and only reconnect when the unit is moving.
3.0 Specifications NOTE: All specifications are subject to change without notice.
4.0 Website The EziTrak® Nano Mobile can be sent commands from the website when it is connected. These commands are primarily used to change the Position (GPS) UPDATE Rate of the unit to the website. These commands are also used to change Unit settings such as the NAME or PIN Number. USB Utility The EziTrak® Nano Mobile can also be configured by the USB Utility software program. This program can be used for the following tasks: • Set up & configure single units.
5.0 Command Structure All commands can be sent to the unit via SMS, GPRS or USB. 1. SMS command SMS Commands must be preceded by the PIN. EXAMPLES: 1234.PIN.54321 54321.NAME.My Name 2. GPRS or USB command All commands can be sent to the unit using GPRS (over the internet) or via the USB Port. No PIN is necessary when using GPRS or the USB Port. EXAMPLES: 14 SET.PIN.54321 SET.NAME.My Name Rojone Pty. Limited – EziTrak® Nano A.B.
6.0 Command Set The following commands can be used to alter the settings and the behaviour of any unit. Commands can be sent to any unit using the Website or via SMS Text or via the Mini B USB Port using the Utility provided by Rojone. Commands are listed in alphabetical group order. Parameter values in RED are the DEFAULT SETTINGS. NOTE: Commands that do not have a Default Setting are COMMANDS ONLY as they do not have a user settable parameter. ACCELEROMETER and MAN DOWN ACCEL.ON/OFF ON ACCEL.RANGE.
BLACKBOX BLACKBOX.ON/OFF ON BLACKBOX.CLEAR BLACKBOX.DAYS.ALL/MON/TUE/WED/THU/FRI/SAT/SUN ALL BLACKBOX.RATE.x 5 Seconds BLACKBOX.FULL.x 20 Percent BLACKBOX.GET.ALL BLACKBOX.GET.x BLACKBOX.RECORD.MRMC/SRMC/EVENT/DEBUG/ALL ALL BLACKBOX? BLACKBOX.DEFAULT BUZZER BUZZER.ON/OFF ON BUZZER.GPRSON.x 2 Short Beeps BUZZER.GPRSOFF.x 2 Long Beeps BUZZER.GPSLOCK.x 3 Short Beeps BUZZER.GPSUNLOCK.x 3 Long Beeps BUZZER.LOWBAT.x Short and Long Beeps 1 BUZZER? BUZZER.DEFAULT EMAIL EMAIL.AUTO.
GEO GEO.LEARNPOSITION.x.r.M/KM GEO.SETHOMEBASE GEO.SETPOSITION.x.lat,lon,R.M/KM GEO.ENTRY.ON/OFF OFF GEO.EXIT.ON/OFF OFF GEO.GETPOSITION.x(0-5) GEO.SMS.ON/OFF OFF GEO.SMS.phonenumber blank GEO? GEO.DEFAULT GPRS GPRS.ON/OFF ON GPRS.GETSETTINGS GPRS.USERNAME.username blank GPRS.PASSWORD.password blank GPRS.APN.x telstra.internet GPRS.AUTO APN.ON/OFF ON GPRS.CONNECT GPRS.CLOSE GPRS.DISCONNECT GPRS.EXIT GPRS.RESTART GPRS.RECONNECTTIMER.x 10 Seconds GPRS.MOVINGCONNECT.ON/OFF OFF GPRS.
GPS GPS.ON/OFF ON GPS.FORMAT.DMS/DDM/DD.NSEW/MATH DMS.NSEW GPS.LOCKTIMER.ON/OFF OFF GPS.LOCKTIMER.x 0 Seconds GPS.MODE.CAR/PEDESTRIAN CAR GPS.ONLINE/OFFLINE GPS.RMC GPS.RESTART GPS.SIGNALWATCHDOG.ON/OFF ON GPS.SIGNALWATCHDOGTIMER.x 60 Seconds GPS.SIGNALWATCHDOGUNLOCK.ON/OFF ON GPS.SIGNALWATCHDOGFIX.1/2/3 (No Fix/2D/3D) 3 GPS.SIGNALWATCHDOGHDOP.x 5.0 GPS.SIGNALWATCHDOGVDOP.x 5.0 GPS.SIGNALWATCHDOGPDOP.x 5.0 GPS.SIGNALWATCHDOGSATS.x 3 GPS? GPS.DEFAULT INFORMATION INFO.ALL INFO.
INFO.POWER INFO.RMC INFO.SETTINGS INFO.SMS.phonenumber.text INFO.STATUS INFO.VERSION LOG LOG.ON/OFF OFF LOG.CLEAR LOG.GET LOG.INFO LOG.RESET LOG.START.[yy]yy/mm/dd,hh:mm:ss LOG.END.[yy]yy/mm/dd,hh:mm:ss LOG.ENGINEHOUR.x 0 Hours LOG.ODOMETER.x 0 Hours LOG.SERVICEHOUR.x 0 Hours LOG.TRIGGERHOUR.x 0 Hours LOG? LOG.DEFAULT MAN DOWN ALARM MDA.ON/OFF ON MDA.AUTORESET.ON/OFF OFF MDA.CLEAR MDA.SMS.ON/OFF OFF MDA.SMS.phonenumber blank MDA.TIMER.x (Auto Reset Timer) 60 Seconds MDA? MDA.
MODE MODE.CAR.ON/OFF OFF MODE.CAR.DELAY.x 5 MODE.IDLE.ON/OFF OFF Minutes MODE? MODE.DEFAULT PANIC/MARKER BUTTON PANIC.ON/OFF ON PANIC.DELAY.x 1 PANIC.SMS.ON/OFF OFF PANIC.SMS.phonenumber blank Second PANIC? PANIC.DEFAULT SET Command SET.ID.x 1 SET.MEASURE.KILOMETRES/MILES/NAUTICALMILES SET.PANIC/MARKER PANIC SET.NAME.x XXX SET.PIN.x 1234 Kilometres SET? SET.DEFAULT TEST Command These commands are for factory debugging only. 20 Rojone Pty. Limited – EziTrak® Nano A.B.
TIME Command TIME.LOCAL TIME.ZONE.[+/-]x 10 TIME.DLS.ON/OFF OFF TIME.DLS.START.x,END.y TIME.DLS.CLEAR TIME? TIME.DEFAULT Australian Daylight Savings settings from 2011 to 2013 Sunday 2 October 2011 to 1 April 2012 TIME.DLS.START.10/02,END.04/01 Sunday 7 October 2012 to 7 April 2013 TIME.DLS.START.10/07,END.04/07 Sunday 6 October 2013 to 6 April 2014 TIME.DLS.START.10/06,END.04/06 General Commands RAW RMC POSITION EXIT GPSONLINE GPSOFFLINE GETALLSETTINGS Rojone Pty. Limited – EziTrak® Nano A.B.
7.0 Detailed Command Set The following commands can be used to alter the settings and the behaviour of any unit. Commands can be sent to any unit using the Website or via SMS Text or via the Mini B USB Port using the Utility provided by Rojone. Commands are listed in alphabetical group order. Parameter values in RED are the DEFAULT SETTINGS. NOTE: Commands that do not have a Default Setting are COMMANDS ONLY as they do not have a user settable parameter. ACCELEROMETER and MAN DOWN ACCEL.
ACCEL.DDELAY.x 3 Seconds This command is used to SET the MAN DOWN Delay Timer. The unit will begin counting when it Detects the unit is at a larger angle than the “Y” Angle Threshold. If the unit remains at an angle Larger than the Threshold for the DDELAY Time in seconds, it will send a MAN DOWN Event to the server, when Enabled, See MDA – Man Down Alarm. ACCEL.UDELAY.x 4 Seconds This command is used to SET the MAN UP Delay Timer.
BLACKBOX BLACKBOX.ON/OFF ON This command is used to Enable and Disable the Blackbox Recorder. It recommended to always have this function ON as it is required internally. The Blackbox is a Circular Buffer so the oldest data is overwritten by the newest data. The device is designed to Email ALL data before it ever gets overwritten anyway.
BLACKBOX.RECORD.MRMC/SRMC/EVENT/DEBUG/ALL ALL This command is used to LIMIT the strings recorded into the blackbox. The default is to record ALL types of strings including GPS, Moving and Stationary as well as general Event strings and Debug strings. Turning OFF the Event and Debug strings would effectively provide more memory space for GPS strings. As the blackbox system is Automatic, this is generally not necessary.
This command simply resets all Buzzer settings to factory defaults. EMAIL EMAIL.AUTO.ON/OFF ON This command is used to Enable and Disable the Automatic EMAIL system used by the Blackbox Recorder. It is recommended to always have this function ON as it is required internally. EMAIL.BLACKBOX This is a Manual command which forces the blackbox to Email its contents to the website immediately. Normally the Email system is fully Automatic.
homebase point using the command, INFO.HOMEBASE at any time. The unit will return its location relative to its homebase as example “10.3 Kilometres North of Homebase”. GEO.SETPOSITION.x.lat,lon,R.M/KM This command is used to TELL the unit to LEARN a GIVEN position as a GEO Fence. This GEO Fence is an Imaginary CIRCULAR fence around the Longitude and Latitude Coordinates provided in the command.
This command simply resets all GEO Fence settings to factory defaults. GPRS GPRS.ON/OFF ON This command is used to Enable and Disable the GPRS Function. It is recommended to always have this function ON as it is required internally. GPRS.GETSETTINGS GPRS.USERNAME.username blank GPRS.PASSWORD.password blank GPRS.APN.x telstra.internet GPRS.AUTO APN.ON/OFF ON GPRS.CONNECT GPRS.CLOSE GPRS.DISCONNECT GPRS.EXIT GPRS.RESTART GPRS.RECONNECTTIMER.x 10 Seconds GPRS.MOVINGCONNECT.ON/OFF OFF GPRS.
GPS GPS.ON/OFF ON This command is used to Enable and Disable the onboard GPS Receiver. It is recommended to always have this function ON as it is required internally. GPS.FORMAT.DMS/DDM/DD.NSEW/MATH DMS.NSEW GPS.LOCKTIMER.ON/OFF OFF GPS.LOCKTIMER.x 0 GPS.MODE.CAR/PEDESTRIAN CAR Seconds GPS.ONLINE/OFFLINE GPS.RMC GPS.RESTART GPS.SIGNALWATCHDOG.ON/OFF ON GPS.SIGNALWATCHDOGTIMER.x 60 Seconds GPS.SIGNALWATCHDOGUNLOCK.ON/OFF ON GPS.SIGNALWATCHDOGFIX.1/2/3 (No Fix/2D/3D) 3 GPS.
INFORMATION INFO.ALL INFO.ADDRESS INFO.BATTERY INFO.EZ INFO.EZRMC INFO.HOMEBASE INFO.LASTPOSITION INFO.LOG INFO.POSITION INFO.POWER INFO.RMC INFO.SETTINGS INFO.SMS.phonenumber.text INFO.STATUS INFO.VERSION LOG LOG.ON/OFF OFF This command is used to Enable and Disable the LOG Function LOG.CLEAR LOG.GET LOG.INFO LOG.RESET LOG.START.[yy]yy/mm/dd,hh:mm:ss LOG.END.[yy]yy/mm/dd,hh:mm:ss LOG.ENGINEHOUR.x 0 Hours LOG.ODOMETER.x 0 Hours LOG.SERVICEHOUR.x 0 Hours LOG.TRIGGERHOUR.x 0 Hours LOG? LOG.
MAN DOWN ALARM MDA.ON/OFF ON This command is used to Enable and Disable the MAN DOWN Function. MDA.AUTORESET.ON/OFF OFF MDA.CLEAR MDA.SMS.ON/OFF OFF MDA.SMS.phonenumber blank MDA.TIMER.x (Auto Reset Timer) 60 Seconds MDA? MDA.DEFAULT MODE MODE.CAR.ON/OFF OFF This command is used to Enable and Disable the CAR MODE Function MODE.CAR.DELAY.x 5 MODE.IDLE.ON/OFF OFF Minutes This command is used to Enable and Disable the IDLE MODE Function MODE? MODE.DEFAULT PANIC/MARKER BUTTON PANIC.
SET Command SET.ID.x 1 SET.MEASURE.KILOMETRES/MILES/NAUTICALMILES SET.PANIC/MARKER PANIC SET.NAME.x XXX SET.PIN.x 1234 Kilometres SET? SET.DEFAULT TEST Command These commands are for factory debugging only. 32 Rojone Pty. Limited – EziTrak® Nano A.B.N 69 002 691 241 44 Aero Rd, Ingleburn NSW 2565 AUSTRALIA TEL +61 02 9829 1555 FAX +61 02 9605 8812 EMAIL sales@ezitrak.com.au www.ezitrak.com.
TIME Command TIME.LOCAL TIME.ZONE.[+/-]x 10 TIME.DLS.ON/OFF OFF TIME.DLS.START.x,END.y TIME.DLS.CLEAR TIME? TIME.DEFAULT Australian Daylight Savings settings from 2011 to 2014 Sunday 2 October 2011 to 1 April 2012 TIME.DLS.START.10/02,END.04/01 Sunday 7 October 2012 to 7 April 2013 TIME.DLS.START.10/07,END.04/07 Sunday 6 October 2013 to 6 April 2014 TIME.DLS.START.10/06,END.04/06 General Commands RAW RMC POSITION EXIT GPSONLINE GPSOFFLINE GETALLSETTINGS Rojone Pty. Limited – EziTrak® Nano A.B.
Appendix A – Network APN List Access Point Name The command to set the APN is: GPRS.APN.telstra.internet You may find the correct APN for your carrier in the list below. NOTE: Generally no username or password is needed with Australian carriers unless otherwise specified. Telstra ............................................................................ telstra.internet Bigpond.......................................................................... telstra.
Internode (prior to 26/08/09).......................................... splns333a1 iPrimus............................................................................ primuslns1 Optus – Post-Paid.......................................................... connect recently (e.g. 11/2010 for Samsung Galaxy Tab)....... connectCap Optus – Month to Month BYO....................................... CONNECTME Optus – Pre-Paid............................................................
Appendix B – Disclaimer PLEASE READ CAREFULLY This manual is provided as a guide to the typical use of the EziTrak® Nano Mobile. The EziTrak® Nano Mobile accuracy and intercept can be affected by many factors including environmental conditions, general poor signal strength, equipment failure, defects and improper handling/use. It is the user’s responsibility to exercise common prudence and judgement. This device should in no way be relied upon as a substitute for such prudence and judgment.
Appendix C – Warranty Your EziTrak® is warranted for a period of 12 months against defects in material and workmanship affecting normal use EFFECTIVE FROM DATE OF PURCHASE. Please complete the warranty card to secure your warranty guarantee and kindly retain your purchase receipt as proof of purchase, which must be presented if making a claim under the terms of this warranty.
This product is designed and manufactured in Australia. ROJONE Contact Details Head Office 44 Aero Road, Ingleburn NSW 2565 Sydney Australia EMAIL: sales@ezitrak.com.au or sales@rojone.com.au TELEPHONE: 02 8796 7888 Intl: +612 8796 7888 FACSIMILE: 02 8796 7899 Intl: +612 8796 7899 Copyright © 2012 All rights reserved. No part of this publication is to be reproduced in any form or by any means without the express permission of the management of Rojone Pty. Limited – Australia.
This page intentionally left blank. Rojone Pty. Limited – EziTrak® Nano A.B.N 69 002 691 241 44 Aero Rd, Ingleburn NSW 2565 AUSTRALIA TEL +61 02 9829 1555 FAX +61 02 9605 8812 EMAIL sales@ezitrak.com.au www.ezitrak.com.
INTERACTIVE Personnel Monitoring System This product is designed and manufactured by Rojone Pty Ltd Australia. www.rojone.com.au www.ezitrak.com.
