Robot Vacuum and Mop Cleaner Operation Manual Read this operation manual carefully before using the product, and store the manual safely.
CONTENTS Safety instructions ....................................................................................................................................................................................... 2 Warning .......................................................................................................................................................................................................................................................................................
IMPORTANT SAFETY INSTRUCTIONS ead this operation manual before using the product Warning: To avoid injury to yourself and others, and to avoid unnecessary property damage, read carefully before using the product and observe the following “Safety instructions”. The safety instructions are divided into two sections, “Warning” and “Caution”. The “Warning” and “Caution” sections contain important information for safe use of the product and must be followed.
Caution 1. 2. 3. 4. 5. 6. 7. 8. 9. Do not use this product outdoors, on surfaces other than the ground, or in commercial or industrial environments. Do not use the product in environments without protective fencing (such as duplex floors, open balconies, furniture tops). Do not block the air outlet (so as to avoid deformation, product failure, or fire due to overheating). Do not drag the product body (so as not to scratch the ground).
User manual requirements for Part 15& IC wireless product: The user manual shall include the following or similar statement,placed in a prominent location in the text of the manual: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, (2)this device must accept any interference received, including interference that may cause undesired operation.
Product overview Main unit Laser head pressure sensor Function buttons Laser sensor Panel Infrared docking sensor Dust box release button Dust inlet Bumper Mop holder release button EN Infrared docking sensor/Wall detection sensor Charging contact (x2) Infrared sensor TOF wall tracking sensor Spot button • S h o r t p r e s s t o c l e a n a l o ca l i z e d a r e a . T h e r o b o t automatically docks after cleaning.
Mop Mop holder Mop holder release button Disposable mop Dust collector (optional) Flip cover EN LED display Air outlet Infrared lens Transparent cover of dust channel Charging contact Charging port Dust inlet Charging dock (optional) The recharger will not be sold in North America Charging dock indicator Signal emission area Charging port Cord storage slot Charging contact 6
Product installation and charging method 1.
Step 2: When the adapter and the recharger are normally connected and powered on, press and hold the power button of the sweeper to turn on and use it. When the sweeper robot consumes power, it can recharge by itself, or manually short press the recharge button to recharge and charge ； EN Dock button Caution 1. When charging, do not install the mopping module to prevent water seeping from the wet mop and damaging the floor. 2.
EN Step 3: Install the water tank Push the electric water tank and dust box horizontally in the direction of the groove on the main unit until you hear a "click" sound. Step 4: Install the mopping module Push the mopping module buckle in parallel along the electric water tank until you hear a "click" sound. Caution 1. Do not use the mopping function on the carpet. 2.
Turning on/off and cleaning modes Spot button 1. Turning on/off • Short press to clean a localized area. The robot automatically docks after cleaning. • Short press while operating to pause Press and hold the Power button, the Power button indicator is ON and the main unit enters Standby mode. When the main unit is in Idle mode, press and hold the Power button, the indicator slowly turns off and the cleaning cycle is done. Power button • Short press to start a cleaning cycle.
Caution 1. It is recommended to start cleaning when the main unit is on the charging dock or the dust collector. 2. When power is insufficient during cleaning, the main unit will automatically dock on the charging dock or the dust collector and charge itself. It will return to where it left off and resume cleaning after charging is completed. 3. Before using the product, arrange the desks, chairs, household items, floor objects, etc.
Cleaning and maintenance Always turn off the product before any maintenance! Disassembling and installing the main brush Step 2: Clean the main brush Use the cleaning brush to pick up and cut away the hair and fibers entangled on the main brush. It is recommended to replace the main brush every 3-6 months. EN Step 1: Disassemble the main brush Turn the robot vacuum and mop cleaner over, press the main brush cover release button to remove the main brush cover. Take out the main brush and clean it.
Caution 1. Only replace with a side brush supplied by ROIDMI, otherwise, it may lead to damage to the main unit. 2. To avoid scratching yourself, be careful when using a screwdriver to replace the side brush. 3. Install the left and right side brushes correctly onto their respective pins. Disassembling and installing the dust box + water tank (2 in 1) and filter Step 2: Disassemble the filter Press the filter release button on the right of the dust box + water tank (2 in 1) to remove the filter.
Disassembling and installing the mop Step 2: Clean the mop Rinse the mop with clean water. Air-dry completely before reinstalling to prevent dust from clumping during the next use. EN Step 1: Disassemble the mop Remove the mopping module from the dust box + water thank (2 in 1), and remove the mop from the mopping module. Caution 1. Only replace with a mop supplied by ROIDMI, otherwise, it may lead to ineffective cleaning. 2. Be sure to remove and clean the mop to prevent dirty water flowing back. 3.
Step 3: Clean the filter Rinse the dust box filter with clean water. Air-dry completely before reinstalling to prevent dust from clumping during the next use. Clean the charging dock (optional) EN Step 1: Clean the charging contact Check whether there is dirt on the charging contacts. Wipe and clean the charging contacts with a soft clean cloth to keep it clean and free of debris. Caution 1. Use a dry cloth to clean the main unit’s sensors, infrared sensors and charging contacts.
Step 2: Clean the dust channel If the dust collector does not work while powered on and the dust bag is not full, firstly disconnect it from the power supply and check whether the dust channel is blocked. If it is blocked, use a screwdriver to open its transparent cover and clear out the obstructions. Step 3: Clean the infrared lens and charging contacts Wipe and clean the infrared lens and charging contacts with a soft clean cloth to keep it clean and free of debris.
Error message Solution If the bumper is stuck, remove the debris and briskly tap the bumper several times to dislodge any debris that may be trapped underneath. Error 2: Check if the bumper is stuck. If the product is trapped because of insufficient space, move it to a new location and start it. If the alert continues, contact the customer service. If the main unit is suspended in the air, move it to a new location and start it.
Error message Solution Error 20: Clean the filter. Remove the filter and clean it. Tip: Resetting the system can fix some errors. Question type Solution Cannot power on If the battery power is insufficient, dock the main unit on the charging dock and fully charge it before next use. If the battery temperature is too low or too high, use the product at temperatures of 0-40 °C. Cannot charge Make sure both ends of the charging dock’s power cable are firmly plugged in.
EN Technical data Product name Robot vacuum and mop cleaner Product model SDJ01RM Rated operating voltage 14.4 V Rated power 50 W Lithium battery capacity 5200mAh Rated charging voltage 24 V Net weight ca. 3.5 kg Dimensions 355 x 355 x 100 mm Charging time ca. 250 minutes Noise level (ECO/STANDARD/BOOST/MAX) ＜75dB（A） Dust box capacity 300 ml Cleaning time ca.
Disposal Correct disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
Warranty card Customer name Product name and model Mailing address Main unit serial number Contact information Purchase date This warranty card contains customers’ personal information, keep it safe Maintenance records Fault description Replacement parts Servicing engineer Servicing date EN Servicing center Correct disposal of this product for indoor use only class Ⅱ equipment protection fuse: T 3.
