Datasheet

Technical Note
10/48
BA4558F,BA4558R F/FV/FVM,BA4560F,BA4560RF/FV/FVM,BA4564RFVBA4580RF/FVM,BA4584FV,
BA4584RF/FV,BA8522RF/FV/FVM,BA15218F,BA14741F,BA15532F,BA4510F/FV,BA2115F/FVM
www.rohm.com
2011.08 - Rev.B
© 2011 ROHM Co., Ltd. All rights reserved.
Absolute maximum rating (Ta=25[])
BA15218/BA14741/BA15532 family
Parameter Symbol
Ratings
Unit
BA15218 family BA14741 family BA15532 family
Supply Voltage VCC-VEE 36 42 V
Differential Input Voltage
(*22)
Vid VCC-VEE ±0.5
(*23)
V
Input Common-mode voltage range Vicm VEEVCC V
Operating Supply Voltage Vopr 432 (±2±16) 436 (±2±18) 640 (±3±20) V
Input Current Ii - ±10 mA
Operating Temperature Topr -40+85 -20+75
Storage Temperature Tstg -55+125
Output Short Current
(*24)
Iomax ±50 - mA
Output Short Time
(*24)
Ts -
unlimited
(only 1CH short)
unlimited Sec
Note: Absolute maximum rating item indicates the condition which must not be exceeded.
Application of voltage in excess of absolute maximum rating or use out absolute maximum rated temperature environment may cause
deterioration of characteristics.
(*22) The voltage difference between inverting input and non-inverting input is the differential input voltage.
Then input terminal voltage is set to more than VEE.
(*23) Don’t over input current ±10mA. Built-in resistor for protection because of over current with differential input voltage above 0.5 .
(*24) Limit within Pd.
Electrical characteristics
BA15218 family (Unless otherwise specified VCC=+15[V], VEE=-15[V], Ta=25[])
Parameter Symbol
Temperature
Range
Limits
Unit Condition
BA15218F
Min. Typ. Max.
Input Offset Voltage
(*25)
Vio 25 - 0.5 5.0 mV Rs10[k]
Input Offset Current
(*25)
Iio 25 - 5 200 nA
Input Bias Current
(*26)
Ib 25 - 50 500 nA
Large Signal Voltage Gain Av 25 86 110 - dB RL2[k], Vo=±10[V]
Input Common-mode Voltage Range Vicm 25 ±12 ±14 - V
Common-mode Rejection Ratio CMRR 25 70 90 - dB Rs10[k]
Power Supply Rejection Ratio PSRR 25 76 90 - dB Rs10[k]
Supply Current ICC 25 - 5.0 8.0 mA Vin=0, RL=
Maximum Output Voltage
VOH 25 ±12 ±14 - V RL10[k]
VOL 25 ±10 ±13 - V RL2[k]
Slew Rate SR 25 - 3.0 - V/μs GV=0[dB], RL=2[k]
Gain Bandwidth Product GBW 25 - 10 - MHz f=10[KHz]
Input Referred Noise Voltage Vn 25 - 1.0 - μVrms
RS=1[k],
BW=20[Hz]30[kHz], RIAA
Channel Separation CS 25 - 120 - dB f=1[kHz] input referred
(*25) Absolute value
(*26) Current direction: Since first input stage is composed with PNP transistor, input bias current flows out of IC.