R&S®RTE Oscilloscope Specifications Data Sheet | Version 20.00 year RTE_dat-sw_en_3607-1494-22_v2000_cover.indd 1 22.07.
Version 20.00, July 2019 CONTENTS Definitions ....................................................................................................................................................................... 4 Base unit .......................................................................................................................................................................... 5 Vertical system ................................................................................................
Version 20.00, July 2019 R&S®RTE-K9................................................................................................................................................................................... 31 R&S®RTE-K10................................................................................................................................................................................. 32 R&S®RTE-K18...........................................................................................
Version 20.00, July 2019 Definitions General Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation Specified environmental conditions met Recommended calibration interval adhered to All internal automatic adjustments performed, if applicable Specifications with limits Represent warranted product performance by means of a range of values for the specified parameter.
Version 20.00, July 2019 Base unit Vertical system Input channels R&S®RTE1022 R&S®RTE1024 R&S®RTE1032 R&S®RTE1034 R&S®RTE1052 R&S®RTE1054 R&S®RTE1102 R&S®RTE1104 R&S®RTE1152 R&S®RTE1154 R&S®RTE1202 R&S®RTE1204 2 channels 4 channels 2 channels 4 channels 2 channels 4 channels 2 channels 4 channels 2 channels 4 channels 2 channels 4 channels 50 Ω ± 1.5 % 1 MΩ ± 1 % || 17 pF ± 1 pF (meas.
Version 20.00, July 2019 Maximum input voltage Position range Offset range at 50 Ω Offset range at 1 MΩ at 50 Ω at 1 MΩ input sensitivity 200 mV/div to 1 V/div 50 mV/div to ≤ 200 mV/div 500 μV/div to ≤ 50 mV/div input sensitivity 900 mV/div to 10 V/div 80 mV/div to ≤ 900 mV/div 500 μV/div to ≤ 80 mV/div Offset accuracy DC measurement accuracy Channel-to-channel isolation (each channel at same input sensitivity) RMS noise floor at typ.
Version 20.00, July 2019 Horizontal system Timebase range Channel deskew Reference position Trigger offset range Modes Channel-to-channel skew Timebase accuracy Delta time accuracy max. min.
Version 20.00, July 2019 Ultra segmented mode continuous recording of waveforms in acquisition memory without interruption due to visualization max. realtime waveform acquisition > 1 600 000 waveforms/s rate min. blind time between consecutive < 400 ns acquisitions Differential signals General description Input channels Differential signal Common mode signal Maximum number of outputs Calculation of differential and common mode signals from p part and n part connected to separate input channels.
Version 20.
Version 20.00, July 2019 Advanced trigger modes Sequence trigger (A/B trigger) Serial bus trigger External trigger input Trigger out 10 triggers on B event after occurrence of A event; delay condition after A event specified either as time interval or number of B events A event any trigger mode B event edge, glitch, width, runt, window, timeout, interval, slew rate optional see dedicated triggering and decoding options 50 Ω ± 1.5 % (meas.), input impedance 1 MΩ ± 1 % || 14 pF (meas.) max.
Version 20.00, July 2019 RF characteristics 4 Sensitivity/noise density Noise figure Signal-to-noise ratio Absolute amplitude accuracy Spurious-free dynamic range Second-harmonic distortion Third-harmonic distortion 4 at 1.001 GHz (measurement of the power spectral density at 1.001 GHz at input sensitivity 1 mV/div, corresponding to –36 dBm input range of the oscilloscope, using the FFT with center frequency 1.
Version 20.
Version 20.
Version 20.
Version 20.
Version 20.00, July 2019 General data Display type resolution Temperature Temperature loading operating temperature range storage temperature range Climatic loading Altitude Operating Nonoperating Mechanical resistance Vibration 0 °C to +45 °C –40 °C to +70 °C +25° C/+40 °C at 85 % rel. humidity cyclic, in line with IEC 60068-2-30 up to 3000 m above sea level up to 4600 m above sea level sinusoidal random Shock EMC RF emission Immunity 5 10.
Version 20.00, July 2019 Power supply AC supply 100 V to 240 V at 50 Hz to 60 Hz and 400 Hz, max. 3.3 A to 1.5 A, in line with MIL-PRF-28800F section 3.5 max. 300 W in line with IEC 61010-1, EN 61010-1, CAN/CSA-C22.2 No. 61010-1-04, UL 61010-1 Power consumption Safety Mechanical data Dimensions W×H×D Weight without options, nominal 427 mm × 249 mm × 204 mm (16.81 in × 9.80 in × 8.03 in) 8.6 kg (18.
Version 20.
Version 20.
Version 20.
Version 20.
Version 20.00, July 2019 Amplitude range 6 DC offset range Frequency accuracy sine, square/pulse, ramp, pulse, exponential rise, exponential fall into 50 Ω 10 mV to 6 V (Vpp) (frequency ≤ 50 MHz), 10 mV to 4 V (Vpp) (frequency > 50 MHz) into open circuit 20 mV to 12 V (Vpp) (frequency ≤ 50 MHz), 20 mV to 8 V (Vpp) (frequency > 50 MHz) sine cardinal (sinc) into 50 Ω 10 mV to 3 V (Vpp) into open circuit 20 mV to 6 V (Vpp) Gauss, Lorentz into 50 Ω 10 mV to 2.
Version 20.00, July 2019 R&S®RTE-B10 Additional GPIB interface Function interface in line with IEC 625-2 (IEEE 488.2) SCPI 1999.0 24-pin Amphenol female SH1, AH1, T6, L4, SR1, RL1, PP1, DC1, DT1, C0 Command set Connector Interface functions R&S®RTE-B18 Additional removable solid state disk Disk type Disk size Firmware solid state disk nom.
Version 20.
Version 20.
Version 20.00, July 2019 LIN serial triggering and decoding Protocol configuration version bit rate device list auto threshold setup Trigger source trigger event setup identifier setup data setup Decode source (TX and RX) display type color coding Search data format search event setup event settings 26 Rohde & Schwarz R&S®RTE Oscilloscope 1.3, 2.x or SAE J602; mixed traffic is supported standard bit rate (1.2/2.4/4.8/9.6/10.417/ 19.
Version 20.00, July 2019 R&S®RTE-K4 FlexRay™ serial triggering and decoding Protocol configuration signal type channel type bit rate device list auto threshold setup Trigger source trigger event setup header setup indicator bits setup identifier setup payload length setup cycle count data setup Decode source display type color coding Search data format search event setup event settings single-ended, differential, logic channel A, channel B standard bit rates (2.5/5.0/10.
Version 20.
Version 20.
Version 20.00, July 2019 R&S®RTE-K7 ARINC 429 triggering and decoding Protocol configuration signal type bit rate polarity device list auto threshold setup timing Trigger trigger event setup label + data setup error condition Decode source display type color coding Search data format search event setup event settings single-ended high (100 kbit/s) low (12 kbit/s to 14.5 kbit/s) A leg, B leg associate frame identifier with symbolic ID assisted threshold configuration min.
Version 20.
Version 20.
Version 20.00, July 2019 R&S®RTE-K18 Spectrum analysis General description Spectrogram Logarithmic frequency x-axis Waveform measurements Waveform math The R&S®RTE-K18 spectrum analysis allows advanced signal analysis in the frequency domain.
Version 20.00, July 2019 R&S®RTE-K31 Power analysis General description Input Switching/control loop Power path Output Deskew Reporting 34 The R&S®RTE-K31 power analysis option extends the R&S®RTE firmware with measurement functionality focused on switched mode power supplies (SMPS) and DC/DC converters.
Version 20.00, July 2019 R&S®RTE-K35 Bus analysis General description Measurements The R&S®RTE-K35 bus analysis option adds bus measurements and analysis functions for dedicated protocols.
Version 20.00, July 2019 R&S®RTE-K50 Manchester and NRZ serial triggering and decoding Protocol configuration signal type Frame format Trigger Decode Search Filter 7 selectable, one channel, differential or single-ended, two channel, differential or single-ended bit rate auto detected, selectable/adjustable auto threshold setup assisted threshold configuration source (SDATA) analog, math.
Version 20.
Version 20.
Version 20.00, July 2019 R&S®RTE-K60 USB 1.0/1.1/2.
Version 20.
Version 20.
Version 20.00, July 2019 Ordering information Designation Type Order No. Base unit (including standard accessories: R&S®RTE-ZP10 500 MHz passive probe per channel, accessories bag, quick start guide, CD with manual, power cord) Oscilloscope 200 MHz, 5 Gsample/s, 50/100 Msample, 2 channels R&S®RTE1022 1326.2000.22 200 MHz, 5 Gsample/s, 50/200 Msample, 4 channels R&S®RTE1024 1326.2000.24 350 MHz, 5 Gsample/s, 50/100 Msample, 2 channels R&S®RTE1032 1326.2000.
Version 20.00, July 2019 Designation Analysis Spectrum analysis Power analysis Bus analysis Probes 500 MHz, passive, 10:1, 1 MΩ || 9.5 pF, max. 400 V 400 MHz, passive, high-voltage, 100:1, 50 MΩ || 7.5 pF, 1 kV (RMS) 400 MHz, passive, high-voltage, 1000:1, 50 MΩ || 7.5 pF, 1 kV (RMS) 1.0 GHz, active, 1 MΩ || 0.8 pF 1.0 GHz, active, 1 MΩ || 0.8 pF, R&S®ProbeMeter, micro button 1.5 GHz, active, 1 MΩ || 0.8 pF, R&S®ProbeMeter, micro button 3.0 GHz, active, 1 MΩ || 0.
Version 20.00, July 2019 Warranty Base unit All other items 12 Options Extended warranty, one year Extended warranty, two years Extended warranty with calibration coverage, one year Extended warranty with calibration coverage, two years Extended warranty with accredited calibration coverage, one year Extended warranty with accredited calibration coverage, two years 3 years 1 year R&S®WE1 R&S®WE2 R&S®CW1 R&S®CW2 R&S®AW1 R&S®AW2 Please contact your local Rohde & Schwarz sales office.
Version 20.
Version 20.
Version 20.
Service that adds value Worldwide Local and personalized ❙ Customized and flexible ❙ Uncompromising quality ❙ Long-term dependability ❙ ❙ Rohde & Schwarz The Rohde & Schwarz electronics group offers innovative solutions in the following business fields: test and measurement, broadcast and media, secure communications, cybersecurity, monitoring and network testing.
