User manual

53
Technical Data
15 Technical Data
1
Technical Data
R&S®HMO1002
50/70/100MHz 2-channel mixed signal oscilloscopes
Firmware: ≥ 5.0
All data valid at 23°C after 30 minute warm-up.
Display
Display 16,5 cm (6,5“) VGA Color Display
Resolution 640 (H) x 480 (V) Pixel
Backlight 400 cd/m
2
(LED)
Display range in horizontal direction
without menu bar 12 Div (600 Pixel)
with menu bar 10 Div (500 Pixel)
Display range in vertical direction 8 Div (400 Pixel)
with Virtual Screen usage 20 Div
Color depth 256 colors
Levels of trace brightness 32
Trace display pseudo-color, inverse brightnes
Vertical System
DSO Mode CH1, CH2
MSO Mode CH1, POD (with Logic Probe HO3508)
Analog channels
Y-bandwidth (-3 dB)
(1 mV, 2 mV)/Div 50 MHz
(5 mV to 10 V)/Div 50 MHz (basic unit)
70 MHz (with HOO572/HV572 option)
100 MHz (with HOO512/HV512 or
HOO712/HV712 option)
Lower AC bandwidth 2 Hz
Bandwidth limitation (switchable) about 20 MHz
Rise time (calculated, 10%-90%)
50 MHz (basic unit) <7 ns
basic unit with 70 MHz option <5 ns
basic unit with 100 MHz option <3.5 ns
DC gain accuracy (all ranges) 3% of full scale
Input sensitivity range
all analog channels 1 mV/Div to 10 V/Div
coarse stepping 13 calibrated steps, 1-2-5 sequence
variable stepping freely between calibrated steps
Impedance 1MΩII16pF±2pF
Coupling DC, AC, GND
Max. input voltage 200 V
p
(derates at 20 db/decade to 5 V
above 100 kHz)
Position range ±5 Div (from center of screen)
Channel isolation 35 dB from DC to specified bandwidth
(same V/Div range)
XY mode CH1, CH2
Inversion selectively all analog channels
Logic channels (with logic probe HO3508)
Thresholds TTL, CMOS, ECL, user-definied (-2 V to
+8 V)
Impedance 100kΩ||4pF
Coupling DC
Max. input voltage 40 Vp
Trigger system
Trigger mode
Auto Triggers automatically also without any
specific trigger event
Technical Data
Normal Triggers only on specific trigger events
Single Triggers once on a trigger event
Trigger indicator Screen and panel (LED)
Trigger sensitivity
up to 5mV/Div 1.5 Div
from 5mV/Div 0.8 Div
Trigger level setting
with auto level adjustablebetweenpeakvaluesofa
signal
without auto level ±5 Div (from center of screen)
external ±5.0 V
Trigger coupling
AC <5 mV/Div: 10 Hz to 65 MHz
>5 mV/Div: 10 Hz to 65/90/130 MHz
DC <5 mV/Div: DC to 65 MHz
>5 mV/Div: DC to 65/90/130 MHz
HF <5 mV/Div: 30 kHz to 65 MHz
>5 mV/Div: 30 kHz to 65/90/130 MHz
selectable filters
LF (low pass) DC to 5 kHz (-3 db), selectable in DC and
auto level mode
 Noiserejection min. level: 1.5 Div (> 5 mV/Div)
selectable with AC, DC and HF coupling
Trigger hold-off auto, 50 ns to 10 s
External trigger input (BNC)
Impedance 1MΩ||16pF±2pF
Trigger level 0.3 V
pp
to 10 V
pp
Max. input voltage 100 V
p
Coupling DC, AC
Trigger output via AUX OUT (BNC)
Functions Pulse output for every acquisition
trigger event, error output on mask
violation
Output level 3 V
Pulse polarity positive
Pulse width >150 ns (trigger event), >0.5 µs (mask
violation)
Trigger types
Edge
Direction rising, falling, both
Trigger coupling auto level AC, DC, HF
Switchable filters LF,noiserejection
Sources all analog and digital channels, AC line,
external (AC, DC)
Pulse width
Polarity positive, negative
Functions equal, not equal, lower, higher, within/
without a range
Pulse duration 16ns to 10s, resolution min. 2ns
Sources all analog channels
Logic
Functions
Boolean operators AND, OR, TRUE, FALSE
time based operators equal, not equal, lower, higher, within/
without a time range, timeout
Duration 16 ns to 10 s, resolution min. 2 ns
States H, L, X
Sources all logic channels