Instructions
Table Of Contents
- Cover
- Contents
- 1 For Your Safety
- 2 Getting Started
- 3 Waveform Setup
- 3.1 Connecting Probes
- 3.2 Vertical Setup
- 3.3 Horizontal Setup
- 3.4 Acquisition Control
- 3.5 Roll Mode
- 3.6 Trigger
- 3.6.1 General Trigger Settings
- 3.6.2 Edge Trigger
- 3.6.3 Glitch Trigger
- 3.6.4 Width Trigger
- 3.6.5 Video/TV Trigger
- 3.6.6 External Trigger (R&S RTH1002)
- 3.6.7 Pattern Trigger (R&S RTH-K19)
- 3.6.8 State Trigger (R&S RTH-K19)
- 3.6.9 Runt Trigger (R&S RTH-K19)
- 3.6.10 Slew Rate Trigger (R&S RTH-K19)
- 3.6.11 Data2Clock Trigger (R&S RTH-K19)
- 3.6.12 Serial Pattern Trigger (R&S RTH-K19)
- 3.6.13 Timeout Trigger (R&S RTH-K19)
- 3.6.14 Interval Trigger (R&S RTH-K19)
- 3.6.15 Window Trigger (R&S RTH-K19)
- 3.6.16 Protocol Trigger (R&S RTH-K1, -K2, -K3, -K9 and -K10)
- 4 Waveform Analysis
- 5 Mask Testing
- 6 Spectrum Analysis
- 6.1 FFT Mode
- 6.2 Spectrum Mode (Option R&S RTH-K18)
- 6.3 Harmonics Measurement (Option R&S RTH-K34)
- 7 Multimeter Measurements
- 8 Data Logging
- 9 Protocol Analysis
- 10 Logic Analyzer (R&S RTH-B1 MSO)
- 11 Frequency Counter (R&S RTH-K33)
- 12 Documenting Results
- 13 General Instrument Setup
- 14 Network Connections
- 15 Remote Control Commands
- 15.1 Conventions used in Command Description
- 15.2 Mode
- 15.3 Waveform Setup
- 15.3.1 Automatic Setup
- 15.3.2 Vertical Setup
- 15.3.3 Horizontal Setup
- 15.3.4 Acquisition Control
- 15.3.5 Trigger
- 15.3.5.1 General Trigger Settings
- 15.3.5.2 Edge Trigger
- 15.3.5.3 Glitch Trigger
- 15.3.5.4 Width Trigger
- 15.3.5.5 Video/TV Trigger
- 15.3.5.6 External Trigger (R&S RTH1002)
- 15.3.5.7 Pattern Trigger (R&S RTH-K19)
- 15.3.5.8 State Trigger (R&S RTH-K19)
- 15.3.5.9 Runt Trigger (R&S RTH-K19)
- 15.3.5.10 Slew Rate Trigger (R&S RTH-K19)
- 15.3.5.11 Data2Clock Trigger (R&S RTH-K19)
- 15.3.5.12 Serial Pattern Trigger (R&S RTH-K19)
- 15.3.5.13 Timeout Trigger (R&S RTH-K19)
- 15.3.5.14 Interval Trigger (R&S RTH-K19)
- 15.3.5.15 Window Trigger (R&S RTH-K19)
- 15.4 Waveform Analysis
- 15.5 Mask Testing
- 15.6 Spectrum Analysis
- 15.7 Digital Multimeter (R&S RTH1002)
- 15.8 Voltmeter (R&S RTH1004)
- 15.9 Counter Mode (R&S RTH-K33)
- 15.10 Data Logging
- 15.11 Protocol Analysis
- 15.12 Logic Analyzer (R&S RTH-B1 MSO)
- 15.13 Documenting Results
- 15.14 General Instrument Setup
- 15.15 WLAN Connection (Option R&S RTH-K200/200US)
- 15.16 User Scripting (R&S RTH-K38)
- Annex
- List of Commands
Remote Control Commands
R&S
®
Scope Rider RTH
363User Manual 1326.1578.02 ─ 15
SPECtrum:WAVeform:MAXimum[:ENABle] <State>
Displays the "Max Hold" spectrum trace.
Parameters:
<State> ON | OFF
*RST: OFF
SPECtrum:WAVeform:MINimum[:ENABle] <State>
Displays the "Min Hold" spectrum trace.
Parameters:
<State> ON | OFF
*RST: OFF
SPECtrum:WAVeform:SPECtrum[:ENABle] <State>
Displays the clear/write spectrum trace.
Parameters:
<State> ON | OFF
*RST: ON
SPECtrum:FREQuency:RESet
Clears the results for previous measurements used in statistical evaluation (see
SPECtrum:WAVeform:AVERage[:ENABle], SPECtrum:WAVeform:MAXimum[:
ENABle], SPECtrum:WAVeform:MINimum[:ENABle] and SPECtrum:
FREQuency:AVERage:COUNt on page 360).
Usage:
Event
15.6.2.2 Cursor Measurements in Spectrum Mode
Special cursor commands are available for the Spectrum mode.
SPECtrum:CURSor<m>:STATe....................................................................................... 363
SPECtrum:CURSor<m>:SOURce....................................................................................364
SPECtrum:CURSor<m>:COUPling.................................................................................. 364
SPECtrum:CURSor<m>:SCPLing....................................................................................364
SPECtrum:CURSor<m>:FREQuency[:VALue]...................................................................365
SPECtrum:CURSor<m>:FREQuency:DELTa?...................................................................365
SPECtrum:CURSor<m>:LEVel[:VALue]?.......................................................................... 365
SPECtrum:CURSor<m>:LEVel:DELTa?............................................................................ 365
SPECtrum:CURSor<m>:SCReen.................................................................................... 366
SPECtrum:CURSor<m>:STATe <State>
Enables or disables the spectrum cursor measurement.
Spectrum Analysis