Instructions
Table Of Contents
- Cover
- Contents
- 1 For Your Safety
- 2 Getting Started
- 3 Waveform Setup
- 3.1 Connecting Probes
- 3.2 Vertical Setup
- 3.3 Horizontal Setup
- 3.4 Acquisition Control
- 3.5 Roll Mode
- 3.6 Trigger
- 3.6.1 General Trigger Settings
- 3.6.2 Edge Trigger
- 3.6.3 Glitch Trigger
- 3.6.4 Width Trigger
- 3.6.5 Video/TV Trigger
- 3.6.6 External Trigger (R&S RTH1002)
- 3.6.7 Pattern Trigger (R&S RTH-K19)
- 3.6.8 State Trigger (R&S RTH-K19)
- 3.6.9 Runt Trigger (R&S RTH-K19)
- 3.6.10 Slew Rate Trigger (R&S RTH-K19)
- 3.6.11 Data2Clock Trigger (R&S RTH-K19)
- 3.6.12 Serial Pattern Trigger (R&S RTH-K19)
- 3.6.13 Timeout Trigger (R&S RTH-K19)
- 3.6.14 Interval Trigger (R&S RTH-K19)
- 3.6.15 Window Trigger (R&S RTH-K19)
- 3.6.16 Protocol Trigger (R&S RTH-K1, -K2, -K3, -K9 and -K10)
- 4 Waveform Analysis
- 5 Mask Testing
- 6 Spectrum Analysis
- 6.1 FFT Mode
- 6.2 Spectrum Mode (Option R&S RTH-K18)
- 6.3 Harmonics Measurement (Option R&S RTH-K34)
- 7 Multimeter Measurements
- 8 Data Logging
- 9 Protocol Analysis
- 10 Logic Analyzer (R&S RTH-B1 MSO)
- 11 Frequency Counter (R&S RTH-K33)
- 12 Documenting Results
- 13 General Instrument Setup
- 14 Network Connections
- 15 Remote Control Commands
- 15.1 Conventions used in Command Description
- 15.2 Mode
- 15.3 Waveform Setup
- 15.3.1 Automatic Setup
- 15.3.2 Vertical Setup
- 15.3.3 Horizontal Setup
- 15.3.4 Acquisition Control
- 15.3.5 Trigger
- 15.3.5.1 General Trigger Settings
- 15.3.5.2 Edge Trigger
- 15.3.5.3 Glitch Trigger
- 15.3.5.4 Width Trigger
- 15.3.5.5 Video/TV Trigger
- 15.3.5.6 External Trigger (R&S RTH1002)
- 15.3.5.7 Pattern Trigger (R&S RTH-K19)
- 15.3.5.8 State Trigger (R&S RTH-K19)
- 15.3.5.9 Runt Trigger (R&S RTH-K19)
- 15.3.5.10 Slew Rate Trigger (R&S RTH-K19)
- 15.3.5.11 Data2Clock Trigger (R&S RTH-K19)
- 15.3.5.12 Serial Pattern Trigger (R&S RTH-K19)
- 15.3.5.13 Timeout Trigger (R&S RTH-K19)
- 15.3.5.14 Interval Trigger (R&S RTH-K19)
- 15.3.5.15 Window Trigger (R&S RTH-K19)
- 15.4 Waveform Analysis
- 15.5 Mask Testing
- 15.6 Spectrum Analysis
- 15.7 Digital Multimeter (R&S RTH1002)
- 15.8 Voltmeter (R&S RTH1004)
- 15.9 Counter Mode (R&S RTH-K33)
- 15.10 Data Logging
- 15.11 Protocol Analysis
- 15.12 Logic Analyzer (R&S RTH-B1 MSO)
- 15.13 Documenting Results
- 15.14 General Instrument Setup
- 15.15 WLAN Connection (Option R&S RTH-K200/200US)
- 15.16 User Scripting (R&S RTH-K38)
- Annex
- List of Commands
Waveform Setup
R&S
®
Scope Rider RTH
49User Manual 1326.1578.02 ─ 15
"Average"
The average is calculated from the data of the current acquisition and
several acquisitions before. The method reduces random noise. It
requires a stable, triggered and periodic signal. The number of
acquisitions for average calculation is defined with Number of Aver-
ages.
"Envelope"
The minimum and maximum values in a sample interval over several
acquisitions are saved. The most extreme values of all acquisitions
build the envelope. The resulting diagram shows two envelope wave-
forms: the minimums (floor) and maximums (roof) representing the
borders in which the signal occurs.
Remote command:
ACQuire:MODE on page 311
Number of Averages
Sets the number of waveforms used to calculate the average waveform.
Remote command:
ACQuire:AVERage:COUNt on page 311
Reset Waveform
Restarts the envelope and average calculation.
Remote command:
ACQuire:ARESet:IMMediate on page 311
Sampling Rate C1 - C4
Shows the number of recorded analog waveform points per second. The sample rate is
the reciprocal value of the resolution.
Sampling Rate D7 - D0
Shows the number of recorded digital waveform points per second. Only available if
the mixed signal option R&S RTH-B1 is installed, and logic channels are active.
Preselected Record Len.
Sets the record length.
"Max"
Sets the maximum record length.
"Middle"
Limits the record length to 12.5 ksample.
"Min"
Limits the record length to 1.25 ksample.
Remote command:
ACQuire:POINts:PRESelect on page 311
Act. Record Len. C1 - C4
Shows the actual record length of analog channels. The actual value can be lower than
the value set with "Preselected Record Len." on page 49, depending on various condi-
tions:
●
Number of active channels
●
"Acquisition Mode" is "Peak Detect" or "High Resolution"
●
If the history option R&S RTH-K15 is installed: "Number of Segments". A high
"Number of Segments" can restrict the record length.
Acquisition Control