Instructions
Table Of Contents
- Cover
- Contents
- 1 For Your Safety
- 2 Getting Started
- 3 Waveform Setup
- 3.1 Connecting Probes
- 3.2 Vertical Setup
- 3.3 Horizontal Setup
- 3.4 Acquisition Control
- 3.5 Roll Mode
- 3.6 Trigger
- 3.6.1 General Trigger Settings
- 3.6.2 Edge Trigger
- 3.6.3 Glitch Trigger
- 3.6.4 Width Trigger
- 3.6.5 Video/TV Trigger
- 3.6.6 External Trigger (R&S RTH1002)
- 3.6.7 Pattern Trigger (R&S RTH-K19)
- 3.6.8 State Trigger (R&S RTH-K19)
- 3.6.9 Runt Trigger (R&S RTH-K19)
- 3.6.10 Slew Rate Trigger (R&S RTH-K19)
- 3.6.11 Data2Clock Trigger (R&S RTH-K19)
- 3.6.12 Serial Pattern Trigger (R&S RTH-K19)
- 3.6.13 Timeout Trigger (R&S RTH-K19)
- 3.6.14 Interval Trigger (R&S RTH-K19)
- 3.6.15 Window Trigger (R&S RTH-K19)
- 3.6.16 Protocol Trigger (R&S RTH-K1, -K2, -K3, -K9 and -K10)
- 4 Waveform Analysis
- 5 Mask Testing
- 6 Spectrum Analysis
- 6.1 FFT Mode
- 6.2 Spectrum Mode (Option R&S RTH-K18)
- 6.3 Harmonics Measurement (Option R&S RTH-K34)
- 7 Multimeter Measurements
- 8 Data Logging
- 9 Protocol Analysis
- 10 Logic Analyzer (R&S RTH-B1 MSO)
- 11 Frequency Counter (R&S RTH-K33)
- 12 Documenting Results
- 13 General Instrument Setup
- 14 Network Connections
- 15 Remote Control Commands
- 15.1 Conventions used in Command Description
- 15.2 Mode
- 15.3 Waveform Setup
- 15.3.1 Automatic Setup
- 15.3.2 Vertical Setup
- 15.3.3 Horizontal Setup
- 15.3.4 Acquisition Control
- 15.3.5 Trigger
- 15.3.5.1 General Trigger Settings
- 15.3.5.2 Edge Trigger
- 15.3.5.3 Glitch Trigger
- 15.3.5.4 Width Trigger
- 15.3.5.5 Video/TV Trigger
- 15.3.5.6 External Trigger (R&S RTH1002)
- 15.3.5.7 Pattern Trigger (R&S RTH-K19)
- 15.3.5.8 State Trigger (R&S RTH-K19)
- 15.3.5.9 Runt Trigger (R&S RTH-K19)
- 15.3.5.10 Slew Rate Trigger (R&S RTH-K19)
- 15.3.5.11 Data2Clock Trigger (R&S RTH-K19)
- 15.3.5.12 Serial Pattern Trigger (R&S RTH-K19)
- 15.3.5.13 Timeout Trigger (R&S RTH-K19)
- 15.3.5.14 Interval Trigger (R&S RTH-K19)
- 15.3.5.15 Window Trigger (R&S RTH-K19)
- 15.4 Waveform Analysis
- 15.5 Mask Testing
- 15.6 Spectrum Analysis
- 15.7 Digital Multimeter (R&S RTH1002)
- 15.8 Voltmeter (R&S RTH1004)
- 15.9 Counter Mode (R&S RTH-K33)
- 15.10 Data Logging
- 15.11 Protocol Analysis
- 15.12 Logic Analyzer (R&S RTH-B1 MSO)
- 15.13 Documenting Results
- 15.14 General Instrument Setup
- 15.15 WLAN Connection (Option R&S RTH-K200/200US)
- 15.16 User Scripting (R&S RTH-K38)
- Annex
- List of Commands
Remote Control Commands
R&S
®
Scope Rider RTH
444User Manual 1326.1578.02 ─ 15
TRIGger:SPI:DATA <Pattern>
Specifies the data pattern to be found on the specified line, in binary format. Enter the
words in MSB first bit order.
Parameters:
<Pattern> String with max. 32 bit in binary format. Characters 0, 1, and X
are allowed.
Example:
TRIGger:SPI:DATA '111000'
TRIGger:SPI:DATA?
<--111000
Specifies a 6 bit pattern. Higher bits are omitted.
TRIGger:SPI:DCONdition <Relation>
Defines how the specified data pattern is compared with the acquired signal. The
instrument triggers if the acquired data is equal or unequal to the pattern.
Parameters:
<Relation> EQUal | NEQual
*RST: EQUal
TRIGger:SPI:DPOSition <BitOffset>
Sets the number of bits before the first bit of the pattern. These bits are ignored. The
first bit after CS or timeout is bit 0.
Parameters:
<BitOffset> Range: 0 to 4095
Increment: 1
*RST: 0
15.11.3.3 SPI Decode Results
The frame suffix <m> selects the frame index for which the result is queried.
The byte suffix <n> selects the byte index for which the result is queried.
BUS:SPI:FCOunt?......................................................................................................... 445
BUS:SPI:FRAMe<m>:DATA?.......................................................................................... 445
BUS:SPI:FRAMe<m>:STATus?....................................................................................... 445
BUS:SPI:FRAMe<m>:STARt?......................................................................................... 445
BUS:SPI:FRAMe<m>:STOP?..........................................................................................446
BUS:SPI:FRAMe<m>:WCOunt?......................................................................................446
BUS:SPI:FRAMe<m>:WORD<n>:MISO?......................................................................... 446
BUS:SPI:FRAMe<m>:WORD<n>:MOSI?......................................................................... 447
BUS:SPI:FRAMe<m>:WORD<n>:STARt?........................................................................ 447
BUS:SPI:FRAMe<m>:WORD<n>:STOP?.........................................................................447
Protocol Analysis