Instructions
Table Of Contents
- Cover
- Contents
- 1 For Your Safety
- 2 Getting Started
- 3 Waveform Setup
- 3.1 Connecting Probes
- 3.2 Vertical Setup
- 3.3 Horizontal Setup
- 3.4 Acquisition Control
- 3.5 Roll Mode
- 3.6 Trigger
- 3.6.1 General Trigger Settings
- 3.6.2 Edge Trigger
- 3.6.3 Glitch Trigger
- 3.6.4 Width Trigger
- 3.6.5 Video/TV Trigger
- 3.6.6 External Trigger (R&S RTH1002)
- 3.6.7 Pattern Trigger (R&S RTH-K19)
- 3.6.8 State Trigger (R&S RTH-K19)
- 3.6.9 Runt Trigger (R&S RTH-K19)
- 3.6.10 Slew Rate Trigger (R&S RTH-K19)
- 3.6.11 Data2Clock Trigger (R&S RTH-K19)
- 3.6.12 Serial Pattern Trigger (R&S RTH-K19)
- 3.6.13 Timeout Trigger (R&S RTH-K19)
- 3.6.14 Interval Trigger (R&S RTH-K19)
- 3.6.15 Window Trigger (R&S RTH-K19)
- 3.6.16 Protocol Trigger (R&S RTH-K1, -K2, -K3, -K9 and -K10)
- 4 Waveform Analysis
- 5 Mask Testing
- 6 Spectrum Analysis
- 6.1 FFT Mode
- 6.2 Spectrum Mode (Option R&S RTH-K18)
- 6.3 Harmonics Measurement (Option R&S RTH-K34)
- 7 Multimeter Measurements
- 8 Data Logging
- 9 Protocol Analysis
- 10 Logic Analyzer (R&S RTH-B1 MSO)
- 11 Frequency Counter (R&S RTH-K33)
- 12 Documenting Results
- 13 General Instrument Setup
- 14 Network Connections
- 15 Remote Control Commands
- 15.1 Conventions used in Command Description
- 15.2 Mode
- 15.3 Waveform Setup
- 15.3.1 Automatic Setup
- 15.3.2 Vertical Setup
- 15.3.3 Horizontal Setup
- 15.3.4 Acquisition Control
- 15.3.5 Trigger
- 15.3.5.1 General Trigger Settings
- 15.3.5.2 Edge Trigger
- 15.3.5.3 Glitch Trigger
- 15.3.5.4 Width Trigger
- 15.3.5.5 Video/TV Trigger
- 15.3.5.6 External Trigger (R&S RTH1002)
- 15.3.5.7 Pattern Trigger (R&S RTH-K19)
- 15.3.5.8 State Trigger (R&S RTH-K19)
- 15.3.5.9 Runt Trigger (R&S RTH-K19)
- 15.3.5.10 Slew Rate Trigger (R&S RTH-K19)
- 15.3.5.11 Data2Clock Trigger (R&S RTH-K19)
- 15.3.5.12 Serial Pattern Trigger (R&S RTH-K19)
- 15.3.5.13 Timeout Trigger (R&S RTH-K19)
- 15.3.5.14 Interval Trigger (R&S RTH-K19)
- 15.3.5.15 Window Trigger (R&S RTH-K19)
- 15.4 Waveform Analysis
- 15.5 Mask Testing
- 15.6 Spectrum Analysis
- 15.7 Digital Multimeter (R&S RTH1002)
- 15.8 Voltmeter (R&S RTH1004)
- 15.9 Counter Mode (R&S RTH-K33)
- 15.10 Data Logging
- 15.11 Protocol Analysis
- 15.12 Logic Analyzer (R&S RTH-B1 MSO)
- 15.13 Documenting Results
- 15.14 General Instrument Setup
- 15.15 WLAN Connection (Option R&S RTH-K200/200US)
- 15.16 User Scripting (R&S RTH-K38)
- Annex
- List of Commands
Remote Control Commands
R&S
®
Scope Rider RTH
432User Manual 1326.1578.02 ─ 15
15.11.2.2 I2C Trigger
TRIGger:I2C:MODE....................................................................................................... 432
TRIGger:I2C:ADNack..................................................................................................... 432
TRIGger:I2C:DRNack.....................................................................................................432
TRIGger:I2C:DWNack.................................................................................................... 432
TRIGger:I2C:ACCess..................................................................................................... 433
TRIGger:I2C:ACONdition................................................................................................433
TRIGger:I2C:ADDRess...................................................................................................433
TRIGger:I2C:DATA.........................................................................................................433
TRIGger:I2C:DCONdition................................................................................................434
TRIGger:I2C:DPOSition..................................................................................................434
TRIGger:I2C:MODE <TriggerType>
Selects the trigger type for I
2
C analysis.
Parameters:
<TriggerType> STARt | RESTart | STOP | NACK | ADDRess | DATA | ADAT
NACK = Missing acknowledge bit
ADAT = combination of address and data condition
For details, see "I2C Trigger" on page 185.
*RST: STARt
TRIGger:I2C:ADNack <TrigOnNoAckForAddress>
Set ON to trigger if no slave recognizes the address.
The command takes effect if TRIGger:I2C:MODE is NACK.
Parameters:
<TrigOnNoAckForAddress>ON | OFF
*RST: ON
TRIGger:I2C:DRNack <NoAckDataRead>
Set ON to trigger if the end of the read process is marked when the master reads data
from the slave. This Nack is sent according to the protocol definition, it is not an error.
The command takes effect if TRIGger:I2C:MODE is NACK.
Parameters:
<NoAckDataRead> ON | OFF
*RST: ON
TRIGger:I2C:DWNack <NoAckDataWrite>
Set ON to trigger if he addressed slave does not accept the written data, and the write
data acknowledge bit is missing.
Protocol Analysis