Instructions
Table Of Contents
- Cover
- Contents
- 1 For Your Safety
- 2 Getting Started
- 3 Waveform Setup
- 3.1 Connecting Probes
- 3.2 Vertical Setup
- 3.3 Horizontal Setup
- 3.4 Acquisition Control
- 3.5 Roll Mode
- 3.6 Trigger
- 3.6.1 General Trigger Settings
- 3.6.2 Edge Trigger
- 3.6.3 Glitch Trigger
- 3.6.4 Width Trigger
- 3.6.5 Video/TV Trigger
- 3.6.6 External Trigger (R&S RTH1002)
- 3.6.7 Pattern Trigger (R&S RTH-K19)
- 3.6.8 State Trigger (R&S RTH-K19)
- 3.6.9 Runt Trigger (R&S RTH-K19)
- 3.6.10 Slew Rate Trigger (R&S RTH-K19)
- 3.6.11 Data2Clock Trigger (R&S RTH-K19)
- 3.6.12 Serial Pattern Trigger (R&S RTH-K19)
- 3.6.13 Timeout Trigger (R&S RTH-K19)
- 3.6.14 Interval Trigger (R&S RTH-K19)
- 3.6.15 Window Trigger (R&S RTH-K19)
- 3.6.16 Protocol Trigger (R&S RTH-K1, -K2, -K3, -K9 and -K10)
- 4 Waveform Analysis
- 5 Mask Testing
- 6 Spectrum Analysis
- 6.1 FFT Mode
- 6.2 Spectrum Mode (Option R&S RTH-K18)
- 6.3 Harmonics Measurement (Option R&S RTH-K34)
- 7 Multimeter Measurements
- 8 Data Logging
- 9 Protocol Analysis
- 10 Logic Analyzer (R&S RTH-B1 MSO)
- 11 Frequency Counter (R&S RTH-K33)
- 12 Documenting Results
- 13 General Instrument Setup
- 14 Network Connections
- 15 Remote Control Commands
- 15.1 Conventions used in Command Description
- 15.2 Mode
- 15.3 Waveform Setup
- 15.3.1 Automatic Setup
- 15.3.2 Vertical Setup
- 15.3.3 Horizontal Setup
- 15.3.4 Acquisition Control
- 15.3.5 Trigger
- 15.3.5.1 General Trigger Settings
- 15.3.5.2 Edge Trigger
- 15.3.5.3 Glitch Trigger
- 15.3.5.4 Width Trigger
- 15.3.5.5 Video/TV Trigger
- 15.3.5.6 External Trigger (R&S RTH1002)
- 15.3.5.7 Pattern Trigger (R&S RTH-K19)
- 15.3.5.8 State Trigger (R&S RTH-K19)
- 15.3.5.9 Runt Trigger (R&S RTH-K19)
- 15.3.5.10 Slew Rate Trigger (R&S RTH-K19)
- 15.3.5.11 Data2Clock Trigger (R&S RTH-K19)
- 15.3.5.12 Serial Pattern Trigger (R&S RTH-K19)
- 15.3.5.13 Timeout Trigger (R&S RTH-K19)
- 15.3.5.14 Interval Trigger (R&S RTH-K19)
- 15.3.5.15 Window Trigger (R&S RTH-K19)
- 15.4 Waveform Analysis
- 15.5 Mask Testing
- 15.6 Spectrum Analysis
- 15.7 Digital Multimeter (R&S RTH1002)
- 15.8 Voltmeter (R&S RTH1004)
- 15.9 Counter Mode (R&S RTH-K33)
- 15.10 Data Logging
- 15.11 Protocol Analysis
- 15.12 Logic Analyzer (R&S RTH-B1 MSO)
- 15.13 Documenting Results
- 15.14 General Instrument Setup
- 15.15 WLAN Connection (Option R&S RTH-K200/200US)
- 15.16 User Scripting (R&S RTH-K38)
- Annex
- List of Commands
Remote Control Commands
R&S
®
Scope Rider RTH
383User Manual 1326.1578.02 ─ 15
Parameters:
<OperationMode> YT | XY | MASK | ROLL | METer | FFT | LOGGer | COUNter |
PROTocol | HARMonic | SPECtrum
*RST: YT (scope mode)
15.7.2 Measurement Configuration
The instrument sets most configuration settings automatically. For most measurement
types, the measurement range is the only parameter that can be set. For temperature
measurements, specific settings are required.
The instrument can adjust the measurement range if autoranging is configured for a
measurement. Otherwise, you can set a fixed measurement range.
To set a fixed measurement range, you can use several commands:
●
METer:CONFigure:<function>
Configures the specified measurement including the measurement range.
See Chapter 15.7.2.1, "METer:CONFigure Commands", on page 383.
●
METer:SENSe:<function>:RANGe:UPPer
Sets the measurement range and turns off autoranging.
See Chapter 15.7.2.2, "METer:SENSe:<function>:RANGe:UPPER Commands",
on page 386.
●
METer:MEASure:<function>
Configures the specified measurement including the measurement range, starts
the measurement, and returns the result.
To enable autoranging, you can use the following commands:
●
METer:SENSe:<function>:RANGe:AUTO
Enables or disables the autoranging. See Chapter 15.7.2.3, "METer:SENSe:<func-
tion>:RANGe:AUTO Commands", on page 388.
●
METer:CONFigure:<function> 'AUTO'
See Chapter 15.7.2.1, "METer:CONFigure Commands", on page 383.
The configuration commands are described in the following chapters:
● METer:CONFigure Commands............................................................................. 383
● METer:SENSe:<function>:RANGe:UPPER Commands.......................................386
● METer:SENSe:<function>:RANGe:AUTO Commands......................................... 388
● AC+DC Current and Voltage Measurements........................................................ 389
● Temperature Measurements................................................................................. 389
15.7.2.1 METer:CONFigure Commands
METer:CONFigure:<function> commands set all internal measurement parame-
ters for the specified measurement. For most measurements, it also sets the measure-
ment range.
To set the range to minimum, maximum, or default value, use the following parameters:
●
METer:CONFigure:<function> MIN
Digital Multimeter (R&S
RTH1002)