Instructions
Table Of Contents
- Cover
- Contents
- 1 For Your Safety
- 2 Getting Started
- 3 Waveform Setup
- 3.1 Connecting Probes
- 3.2 Vertical Setup
- 3.3 Horizontal Setup
- 3.4 Acquisition Control
- 3.5 Roll Mode
- 3.6 Trigger
- 3.6.1 General Trigger Settings
- 3.6.2 Edge Trigger
- 3.6.3 Glitch Trigger
- 3.6.4 Width Trigger
- 3.6.5 Video/TV Trigger
- 3.6.6 External Trigger (R&S RTH1002)
- 3.6.7 Pattern Trigger (R&S RTH-K19)
- 3.6.8 State Trigger (R&S RTH-K19)
- 3.6.9 Runt Trigger (R&S RTH-K19)
- 3.6.10 Slew Rate Trigger (R&S RTH-K19)
- 3.6.11 Data2Clock Trigger (R&S RTH-K19)
- 3.6.12 Serial Pattern Trigger (R&S RTH-K19)
- 3.6.13 Timeout Trigger (R&S RTH-K19)
- 3.6.14 Interval Trigger (R&S RTH-K19)
- 3.6.15 Window Trigger (R&S RTH-K19)
- 3.6.16 Protocol Trigger (R&S RTH-K1, -K2, -K3, -K9 and -K10)
- 4 Waveform Analysis
- 5 Mask Testing
- 6 Spectrum Analysis
- 6.1 FFT Mode
- 6.2 Spectrum Mode (Option R&S RTH-K18)
- 6.3 Harmonics Measurement (Option R&S RTH-K34)
- 7 Multimeter Measurements
- 8 Data Logging
- 9 Protocol Analysis
- 10 Logic Analyzer (R&S RTH-B1 MSO)
- 11 Frequency Counter (R&S RTH-K33)
- 12 Documenting Results
- 13 General Instrument Setup
- 14 Network Connections
- 15 Remote Control Commands
- 15.1 Conventions used in Command Description
- 15.2 Mode
- 15.3 Waveform Setup
- 15.3.1 Automatic Setup
- 15.3.2 Vertical Setup
- 15.3.3 Horizontal Setup
- 15.3.4 Acquisition Control
- 15.3.5 Trigger
- 15.3.5.1 General Trigger Settings
- 15.3.5.2 Edge Trigger
- 15.3.5.3 Glitch Trigger
- 15.3.5.4 Width Trigger
- 15.3.5.5 Video/TV Trigger
- 15.3.5.6 External Trigger (R&S RTH1002)
- 15.3.5.7 Pattern Trigger (R&S RTH-K19)
- 15.3.5.8 State Trigger (R&S RTH-K19)
- 15.3.5.9 Runt Trigger (R&S RTH-K19)
- 15.3.5.10 Slew Rate Trigger (R&S RTH-K19)
- 15.3.5.11 Data2Clock Trigger (R&S RTH-K19)
- 15.3.5.12 Serial Pattern Trigger (R&S RTH-K19)
- 15.3.5.13 Timeout Trigger (R&S RTH-K19)
- 15.3.5.14 Interval Trigger (R&S RTH-K19)
- 15.3.5.15 Window Trigger (R&S RTH-K19)
- 15.4 Waveform Analysis
- 15.5 Mask Testing
- 15.6 Spectrum Analysis
- 15.7 Digital Multimeter (R&S RTH1002)
- 15.8 Voltmeter (R&S RTH1004)
- 15.9 Counter Mode (R&S RTH-K33)
- 15.10 Data Logging
- 15.11 Protocol Analysis
- 15.12 Logic Analyzer (R&S RTH-B1 MSO)
- 15.13 Documenting Results
- 15.14 General Instrument Setup
- 15.15 WLAN Connection (Option R&S RTH-K200/200US)
- 15.16 User Scripting (R&S RTH-K38)
- Annex
- List of Commands
Spectrum Analysis
R&S
®
Scope Rider RTH
136User Manual 1326.1578.02 ─ 15
(3+4) Power level of individual harmonics
For each harmonic and each input channel, a colored bar indicates calculated power
level at the selected harmonic frequency, set in relation to the power level of the funda-
mental frequency. The color of the bar corresponds to the color of the input channel.
The brighter colored bar is the current value, while the darker colored bar is the maxi-
mum value in the current measurement.
Remote command:
HARMonic:RESult<m>:HARMonics<n>:ABSMagnitude[:CURRent]?
on page 377
HARMonic:RESult<m>:HARMonics<n>:ABSMagnitude:MAXimum? on page 377
HARMonic:RESult<m>:HARMonics<n>:ABSMagnitude:MINimum? on page 377
HARMonic:RESult<m>:HARMonics<n>:RELMagnitude[:CURRent]?
on page 380
HARMonic:RESult<m>:HARMonics<n>:RELMagnitude:MAXimum? on page 380
HARMonic:RESult<m>:HARMonics<n>:RELMagnitude:MINimum? on page 380
(5+6) Limit line and check for individual harmonics
If a limit is defined for the individual harmonic, it is indicated in the graphic (see "Limits,
Loaded File" on page 141). If the measured value exceeds the limit line, the back-
ground of the harmonic bar is highlighted red.
Remote command:
HARMonic:RESult<m>:HARMonics<n>:LIMit? on page 378
HARMonic:RESult<m>:HARMonics<n>:LIMCheck? on page 377
HARMonic:RESult<m>:HARMonics<n>:LIMViolation? on page 379
(7) Power level scale
Indicates whether the bargraph results are displayed in percent or dB.
Remote command:
HARMonic:SCALe on page 374
(8) Input channel
Harmonics measurement is performed on the data captured from one of the active
input channels. The measurement can be performed on all channels simultaneously.
The bars and numeric results for each channel are displayed in the same color as the
channel indicator.
Remote command:
CHANnel<m>:STATe on page 303
(9) Result type for numeric results
Either the currently measured numeric values, or the minimum or maximum values can
be displayed. The selected result type is indicated above the diagram. The bargraph
always displays both the current and the maximum values.
In addition, an average over several measurements can be calculated (not indicated in
the diagram.)
Remote command:
HARMonic:STATistic on page 375
Harmonics Measurement (Option R&S
RTH-K34)