Datasheet

23
English
Starting up the grill before barbecueing
lÄ2S@MCÄSGDÄ12+$ÄF@RÄJDSSKDÄFQHKKÄNMÄ@ÄÆQLÄ@MCÄKDUDKÄRTQE@BDÄ!DENQDÄA@QADBTDHMFÄBGDBJÄSG@SÄSGDÄB@SBGDQÄ
tray is properly inserted.
lÄ$UDQXÄSHLDÄXNTÄHMSDMCÄTRHMFÄSGDÄFQHKKÄÆQRSÄBGDBJÄSGDÄF@RÄRTOOKXÄGNRDÄENQÄJHMJRÄBQ@BJRÄRHFMRÄNEÄVD@QÄNQÄBTSRÄ
If damage to the hose is visible, the grill must not be used.
lÄThe hose must only be replaced by an approved replacement hose.
lÄ!DENQDÄTRHMFÄSGDÄFQHKKÄENQÄSGDÄÆQRSÄSHLDÄGD@SÄHSÄSGQNTFGÄVHSGÄSGDÄATQMDQRÄKHSÄ@MCÄSGDÄKHCÄBKNRDCÄENQÄ@SÄKD@RSÄÄ
minutes.
Gas-tightness test
During the test there must be no possible sources of ignition nearby. Do not smoke. Never use a burning match
NQÄM@JDCÄÇ@LDÄSNÄSDRSÄENQÄKD@JRÄ@MCÄ@KV@XRÄB@QQXÄNTSÄSGDÄF@RSHFGSMDRRÄSDRSÄNTSCNNQRÄ/DQENQLÄSGDÄSDRSÄ@ESDQÄ@R-
sembling the gas hose and every time the gas cylinder is connected or replaced and at least once a year.
1. Set the gas regulator knob to position "".
2. Turn on the gas supply at the cylinder.
Ä 4RHMFÄ@ÄAQTRGÄ@OOKXÄ@ÄRN@OÄRNKTSHNMÄ@OOQNWÄÄKHPTHCÄRN@OÄV@SDQÄSNÄ
all gas-carrying components (gas cylinder connection, gas pressure regulator,
gas hose, valve connection).
Alternatively, use a leak-detector spray.
ÄÄ(EÄXNTÄRDDÄÆMDÄATAAKDRÄENQLHMFÄHMÄSGDÄRN@OÄRNKTSHNMÄ@SÄ@MXÄONHMSÄSGHRÄHMCHB@SDRÄ
a leak.
IMPORTANT: the grill must not be used until all leaks have been eliminated. Turn off the gas supply at the gas cylin-
der.
4. Eliminate the leaks by tightening the connections, if possible, or replacing any defective parts.
Ä 1DOD@SÄRSDORÄÄ@MCÄ
6. If the leaks cannot be eliminated, consult your specialist gas appliance retailer.
Lighting the burners
(MRDQSÄSGDÄA@SSDQXÄSXODÄ ÄÄ5ÄHMÄSGDÄHFMHSDQÄVHSGÄSGDÄONRHSHUDÄSDQLHM@KÄE@BHMFÄNTSV@QCRÄ
To do so, unscrew the igniter button (see assembly instructions).
-DUDQÄADMCÄNUDQÄSGDÄNODMÄFQHKKÄ KV@XRÄJDDOÄ@SÄKD@RSÄÄBLÄ@V@XÄEQNLÄSGDÄHFMHSDQÄNODMHMFÄVGDMÄKHFGSHMFÄSGDÄ
grill. Keep your face, hair, loose clothing, etc. well clear.
The large ring burner is at the highest setting when set to MAX and at the lowest setting when set to MIN. It is suita-
AKDÄENQÄBNNJHMFÄ@SÄLDCHTLÄSNÄGHFGÄSDLODQ@STQDRÄ(SÄOQNCTBDRÄSDLODQ@STQDRÄNEÄ@OOQNWÄÄ"ÄSNÄÄ"
3GDÄRL@KKÄQHMFÄATQMDQÄHRÄCDRHFMDCÄENQÄBNNJHMFÄ@SÄKNVÄSDLODQ@STQDRÄ@MCÄNMKXÄG@RÄ@ÄM@QQNVÄQ@MFDÄNEÄ@CITRSLDMSÄRNÄSG@SÄ
the difference between MIN and MAXÄHRÄMNSÄUHRHAKDÄSNÄSGDÄDXDÄ(SÄOQNCTBDRÄSDLODQ@STQDRÄNEÄ@OOQNWÄÄ"ÄSNÄÄ"
3GDÄSVNÄATQMDQRÄSNFDSGDQÄOQNCTBDÄSDLODQ@STQDRÄNEÄTOÄSNÄÄ"ÄVGDMÄRDSÄSNÄMIN
@MCÄÄ"ÄVGDMÄRDSÄSNÄMAX.
Procedure
l If the burner does not light, wait approx. 3 minutes to allow the gas to disperse.
1HRJÄNEÄHMITQX
1DRHCT@KÄF@RÄB@MÄOQNCTBDÄ@MÄDWOKNRHNMKHJDÄÇ@RGÄÇ@LDÄ2DQHNTRÄHMITQXÄ@MCÄDUDMÄCD@SGÄB@MÄADÄSGDÄQDRTKSÄ KV@XRÄ
allow gas to fully disperse before re-lighting or troubleshooting.