User`s manual

Command Reference Manual
1199 v
3.2.3.17 *D - Display Delayed Numbers ................................................................................................ 3-32
3.2.3.18 -STE= - Set Telephony Extension............................................................................................ 3-33
3.2.4 Modulation Control Commands................................................................................................................ 3-34
3.2.4.1 +MS - Modulation Selection..................................................................................................... 3-34
3.2.4.2 +MR - Modulation Reporting Control........................................................................................ 3-35
3.2.4.3 %E - Enable/Disable Line Quality Monitor and Auto-Retrain or Fallback/Fall Forward ........... 3-36
3.2.4.4 %U - Select µ-Law or A-Law Codec Type................................................................................ 3-37
3.2.4.5 B - CCITT or Bell...................................................................................................................... 3-37
3.2.5 Error Control Commands ......................................................................................................................... 3-38
3.2.5.1 +ES - Error Control and Synchronous Mode Selection............................................................ 3-38
3.2.5.2 +EB - Break Handling in Error Control Operation .................................................................... 3-39
3.2.5.3 +ESR - Selective Repeat ......................................................................................................... 3-40
3.2.5.4 +EFCS - 32-bit Frame Check Sequence.................................................................................. 3-40
3.2.5.5 +ER - Error Control Reporting.................................................................................................. 3-40
3.2.5.6 +ETBM - Call Termination Buffer Management ....................................................................... 3-41
3.2.5.7 \B - Transmit Break to Remote................................................................................................. 3-42
3.2.5.8 \K - Break Control..................................................................................................................... 3-43
3.2.5.9 -K - MNP Extended Services ................................................................................................... 3-44
3.2.6 Data Compression Commands ................................................................................................................ 3-44
3.2.6.1 +DS - Data Compression ......................................................................................................... 3-44
3.2.6.2 +DR - Data Compression Reporting ........................................................................................ 3-45
3.2.6.3 %C - Enable/Disable Data Compression ................................................................................. 3-46
3.2.7 V.8/V.8bis Commands.............................................................................................................................. 3-47
3.2.7.1 +A8E - V.8 and V.8bis Operation Controls .............................................................................. 3-47
3.2.7.2 +A8I: - CI Signal Indication ...................................................................................................... 3-48
3.2.8 Synchronous Access Mode Commands .................................................................................................. 3-49
3.2.8.1 +ESA - Configure Synchronous Access Submode.................................................................. 3-49
3.2.8.2 +H - Enable/Disable RPI and Host DSVD................................................................................ 3-50
3.2.8.3 +ITF - Transmit Flow Control Thresholds ................................................................................ 3-51
3.2.9 Diagnostic Commands............................................................................................................................. 3-52
3.2.9.1 #UD –
Last Call Status Report................................................................................................. 3-52
3.2.10 Compatibility Commands ......................................................................................................................... 3-59
3.2.10.1 &L - Leased Line Operation..................................................................................................... 3-59
3.2.10.2 )M - Enable Cellular Power Level Adjustment.......................................................................... 3-59
3.2.10.3 @M - Initial Cellular Power Level Setting................................................................................. 3-59
3.2.10.4 :E - Compromise Equalizer Enable Command......................................................................... 3-60
3.3 S-PARAMETERS ................................................................................................................................................. 3-61
3.3.1.1 S - Read/Write S-Parameter .................................................................................................... 3-61
3.3.2 FACTORY DEFAULTS ............................................................................................................................ 3-61
3.3.3 S-PARAMETER DEFINITIONS................................................................................................................ 3-63
3.3.3.1 S0 - Number of Rings to Auto-Answer..................................................................................... 3-63
3.3.3.2 S1 - Ring Counter .................................................................................................................... 3-63
3.3.3.3 S2 - Escape Character............................................................................................................. 3-63
3.3.3.4 S3 - Carriage Return Character ............................................................................................... 3-63
3.3.3.5 S4 - Line Feed Character......................................................................................................... 3-63
3.3.3.6 S5 - Backspace Character ....................................................................................................... 3-63
3.3.3.7 S6 - Wait Time before Blind Dialing or for Dial Tone ............................................................... 3-64
3.3.3.8 S7 - Wait Time for Carrier, Silence, or Dial Tone..................................................................... 3-64
3.3.3.9 S8 - Pause Time For Dial Delay............................................................................................... 3-64
3.3.3.10 S9 - Carrier Detect Response Time......................................................................................... 3-64
3.3.3.11 S10 - Lost Carrier To Hang Up Delay ...................................................................................... 3-64
3.3.3.12 S11 - DTMF Tone Duration...................................................................................................... 3-65
3.3.3.13 S12 - Escape Prompt Delay (EPD).......................................................................................... 3-65
3.3.3.14 S14 - General Bit Mapped Options Status............................................................................... 3-65
3.3.3.15 S16 - Test Mode Bit Mapped Options Status........................................................................... 3-66
3.3.3.16 S19 - Reserved ........................................................................................................................ 3-66
3.3.3.17 S20 - Reserved ........................................................................................................................ 3-66
3.3.3.18 S21 - V.24/General Bit Mapped Options Status....................................................................... 3-66