User Manual Version 3.0 Instruction Manual

Index Index-5
Rated Volts (27), 11-8
Ready LED
, 12-4
Record of user settings
Advanced access level
, F-1 to F-5
Reference sources
auto
, 7-10
changing
, 7-11
manual
, 7-10
Reflected wave compensation
, 4-6
Reliance, contacting
, 1-1
remote OIM
connecting to NEMA 1 drives
, 2-21
Replacement parts
, 12-23
Reset Meters (200)
, 11-54
Reset To Defalts (197)
, 11-53
Run Boost (70)
, 11-18
S
S curve, 2-12
S Curve % (146)
, 11-37
Safety ground
, 5-4
Save MOP Ref (194)
, 11-52
Save OIM Ref (192)
, 11-51
Save To User Set (199)
, 11-54
Shear pin fault
, 2-10
Shield termination
, 5-4
SHLD terminal
, 5-4
Signal terminal block
,?? to 7-5
Site requirements
, 3-2
Skip bands
, 2-12
Skip Freq Band (87)
, 11-21
Skip Frequency 1 (84)
, 11-21
Skip Frequency 2 (85)
, 11-21
Skip Frequency 3 (86)
, 11-21
Sleep Level (182)
, 11-49
Sleep Time (183)
, 11-49
Sleep-Wake Mode (178)
, 11-46
Sleep-Wake Operation
, 11-47
Sleep-Wake Ref (179)
, 11-48
Slip Comp Gain (122)
, 11-28
Slip RPM @ FLA (121)
, 11-28
Slip RPM Meter (123)
, 11-28
Speed Control
, 2-6
Speed Mode (80)
, 11-18
Speed Pot
, 7-6
Speed Ref A Hi (91)
, 11-24
Speed Ref A Lo (92)
, 11-24
Speed Ref A Sel (90)
, 11-23
Speed Ref Source (213)
, 11-61
Speed reference control
, 7-10
Standard access level parameters
, E-1
Start Inhibits (214)
, 11-61
Start/Acc Boost (69)
, 11-17
Starting the drive using the LCD
OIM
, B-14
Start-Up menu
, 9-2
Start-Up routines
, 9-1
Status 1 @ Fault (227)
, 11-65
Status 2 @ Fault (228)
, 11-65
Stop circuit requirements
, 7-1
Stop Mode A (155)
, 11-39
Stop Mode B (156)
, 11-39
Stop modes
, 2-6
Stop Owner (288)
, 11-72
Stopping the drive using the LCD
OIM
, B-14
Stopping, user-initiated
, 7-2
SV Boost Filter (59)
, 11-15
T
TB Man Ref Hi (97), 11-24
TB Man Ref Lo (98)
, 11-25
TB Man Ref Sel (96)
, 11-24
Testpoint 1 Data (235)
, 11-67
Testpoint 1 Sel (234)
, 11-67
Testpoint 2 Data (237)
, 11-67
Testpoint 2 Sel (236)
, 11-67
Thermal overload protection
, 2-9
Time stamp, fault queue
, 12-10
Torque Current (4)
, 11-5
Torque Perf Mode (53)
, 11-12
Torques, power terminal
, 6-2
Trim Hi (119)
, 11-27
Trim In Select (117)
, 11-26
Trim Lo (120)
, 11-27
Trim Out Select (118)
, 11-27
Troubleshooting
common symptoms and corrective
actions
, 12-19
using the LCD OIM
, 12-23
U
Unbalanced distribution systems, 3-2
Ungrounded distribution systems
, 3-2
User sets, loading and saving using LCD
OIM
, B-8
V
Voltage class, 2-12
Voltage Class (202)
, 11-55
VS Utilities
, 2-22