User Manual Version 1.0 Owner manual

Index Index-5
PI Status (134), 12-36
PI Upper Limit (132)
, 12-35
plugs, sealing unused conduit holes
with
, 6-3
Power Loss Mode (184)
, 12-52
Power Loss Time (185)
, 12-52
power terminal block specifications
, 4-3
Power Up Marker (242)
, 12-72
power wire sizes
, 4-3
power wiring
, 4-1 to 4-3
preset frequency
, 2-9
Preset Speed 1 (101)
, 12-26
Preset Speed 2 (102)
, 12-26
Preset Speed 3 (103)
, 12-26
Preset Speed 4 (104)
, 12-26
Preset Speed 5 (105)
, 12-26
Preset Speed 6 (106)
, 12-26
Preset Speed 7 (107)
, 12-26
process display screen, LCD OIM
, 9-10
Process PI block diagram
, D-1
Process PI loop
, 2-16
product version, how to
determine
, 13-26
Profibus module
, 2-23
program protection
, 11-7
programming basics
, 11-1
Q
Quickstart parameters, 10-3
R
Rated Amps (28), 12-8
Rated kW (26)
, 12-8
Rated Volts (27)
, 12-8
ratings, drive
, 2-3 to 2-6
Ready LED
, 13-3
RECOMM-232
, 2-24
RECOMM-VSU 232
, 2-24
record of user settings
, E-1 to E-6
reference sources
auto
, 7-10
changing
, 7-11
manual
, 7-10
reflected wave compensation
, 4-7
Reliance, contacting
, 1-1
remote OIM
connecting to NEMA 1 drives
, 2-23
connecting to NEMA 4 drives
, 2-24
replacement parts
, 13-23
Reset Meters (200)
, 12-57
Reset To Defalts (197)
, 12-56
RS485 DF1 module
, 2-23
Run Boost (70)
, 12-17
S
S curve, 2-16
S Curve % (146)
, 12-38
safety ground
, 5-3
Save MOP Ref (194)
, 12-55
Save OIM Ref (192)
, 12-54
Save To User Set (199)
, 12-57
sensorless vector performance
, 10-5
serial converter
, 2-24
shear pin fault
, 2-12
shield termination
, 5-4
SHLD terminal
, 5-4
signal terminal block
, 7-2
signal wire size
, 4-5
site requirements
, 3-2
skip bands
, 2-16
Skip Freq Band (87)
, 12-20
Skip Frequency 1 (84)
, 12-20
Skip Frequency 2 (85)
, 12-20
Skip Frequency 3 (86)
, 12-20
Slip Comp Gain (122)
, 12-29
Slip RPM @ FLA (121)
, 12-29
Slip RPM Meter (123)
, 12-29
speed control methods
, 2-8
Speed Mode (80)
, 12-18
Speed Ref A Hi (91)
, 12-24
Speed Ref A Lo (92)
, 12-25
Speed Ref A Sel (90)
, 12-23
Speed Ref Source (213)
, 12-64
speed reference control
, 7-10
speed reference source,
configuring
, 10-6
Start Inhibits (214)
, 12-64
Start/Acc Boost (69)
, 12-17
start/stop control
, 10-5
starting the drive using the LCD
OIM
, 9-17
start-up considerations
, 10-5
Start-Up menu
, 10-2
Start-Up routines
, 10-1
Status 1 @ Fault (227)
, 12-68
Status 2 @ Fault (228)
, 12-68
stop circuit requirements
, 7-1
stop methods
, 2-8
Stop Mode A (155)
, 12-40
Stop Mode B (156)
, 12-40
Stop Owner (288)
, 12-75
stopping the drive using the LCD