User guide

76 Rockwell Automation Publication MP-UM001D-EN-P - September 2013
Appendix A Dimensions
Figure 16 - MP-Series Linear Stages (MPAS-A/B6xxx1/2-VxxSxA)
7.6
(0.30)
239
(9.41)
165
(6.50)
(4X) M6 x 1.0-6H
37.0
(1.46)
12.0 (0.47)
25.0
(0.98)
25.0
(0.98)
167
(6.57)
165
(6.50)
54.5
(2.15)
(4X)
Ø 7.0 (0.28) Thru
Pilot Hole
45.0 (1.80)
130
(5.12)
30.0
(1.18)
125.5
(4.94)
46.8
(1.84)
181.5
(7.15)
8.5
(0.33)
31.9
(1.25)
92.0
(3.62)
150
(5.90)
123.8
(4.87)
Dimensions are in mm (in.)
Detail A
120 (4.72)
Toe Clamp/Tee Nut Spacing
Ø 13.0 (0.51) Through
Access Point to Lubricate
Ball Screw Nut
See Detail A
30.5 (1.20)
Mechanical Overtravel
(4X) M10 x 1.5-6H Through (2 per end cap)
Access point for lubricating linear bearings.
Provision to use lifting hooks (not provided).
Ground Screw
M5 x 0.8-6H
T- Nut
Mount to base by using
M6 x 1.0 hardware (optional accessory).
9.3 (0.37)
Depth, max
(S) Stage Length
(OAL) Overall Length
Toe Clamp is standard for
covered stages. Mount to base
by using M6 x 1.0 socket cap screw.
0.025 / 300 x 300 (0.001 / 12.0 x 12.0)
Flatness requirement for the surface
that this stage is being mounted to.
30.5 (1.20)
Mechanical Overtravel
The overall length (OAL) is measured to
the head of the screws that secure the
motor endcap.
Cat. No.
MPAS-
SOAL
(5 mm/rev)
(1)
OAL
(20 mm/rev)
(2)
Cat. No.
MPAS-
SOAL
(5 mm/rev)
(3)
OAL
(20 mm/rev)
(2)
mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.)
A/B6012x-VxxSxA 470 (18.5) 569 (22.4) 594 (23.4) A/B6036x-VxxSxA 710 (28.0) 809 (31.9) 834 (32.8)
A/B6018x-VxxSxA 530 (20.9) 629 (24.8) 654 (25.7) A/B6042x-VxxSxA 770 (30.3) 869 (34.2) 894 (35.2)
A/B6024x-VxxSxA 590 (23.2) 689 (27.1) 714 (28.1) A/B6054x-VxxSxA 890 (35.0) 989 (38.9) 1014 (39.9)
A/B6030x-VxxSxA 650 (25.6) 749 (29.5) 774 (30.5) A/B6066x-VxxSxA 1010 (39.8) 1109 (43.7) 1134 (44.6)
(1) If MPAS-A/B6xxx-V05S4A linear stage with brake, add 39 mm (1.53 in.) to dimension OAL.
(2) If MPAS-A/B6xxx-V20S4A linear stage with brake, add 39 mm (1.53 in.) to dimension OAL.
(3) If MPAS-A/B6xxx-V05S4A linear stage with brake, add 39 mm (1.53 in.) to dimension OAL.