Manual

ManualsBrandsRockwell Automation ManualsEquipmentLiquiflo AC Drive Panel Mount Kit, M/N 41L4060, Model Number 41L4060PM

Panel Mount Kit for LiquiFlo AC Drives M/N 41L4060

Panel Mount Kit

for LiquiFlo AC Drives

M/N 41L4060

Model Number 41L4060PM

Instruction Manual D2-3460

Product Description

This instruction manual describes how to install an optional panel mount kit on B-frame LiquiFlo AC drives,

M/N 41L4060. The kit comprises items that make panel mounting of a LiquiFlo AC drive safer and easier. Each

kit includes bus bar jumpers, pressure lugs, hose assemblies, and the necessary mounting hardware.

Verifying Kit Contents

Panel mount kit M/N 41L4060PM can be used only with B-frame LiquiFlo AC drives, M/N 41L4060. Kit contents

are listed in table 1, and are indicated by circled item numbers in figure 1.

ATTENTION:Only qualified personnel familiar with the construction and operation of this

equipment and the hazards involved should install, adjust, operate, and/or service this equipment.

Read and understand this instruction manual in its entirety before proceeding. Failure to observe

this precaution could result in severe bodily injury or loss of life.

Table 1 – Panel Mount Kit Contents

Item Description Qty

Part Number

1 Jumper Bus Bar “R”, “S”, “T” 3 179359

2 Pressure Lug, (2) 300 MCM - 6 AWG 6 179440

3 5/16“ Flat Washer, 1” OD, .344” ID, Gr.5 18 601748-26A

4 1/4-20 Hex Nut/Conical Washer 6 401599-11E

5 1/4-20 HHCS Screw, UNC x 1.50 Lg, Gr.5 6 173809

6 5/16-18 Hex Nut/Conical Washer 3 401599-11F

7 5/16-18 HHCS Screw, UNC-2A x 1.25 Lg, Gr.5 3 114581

8 Insulation, 2.0” Dia., 4.00” Lg. 6 417901-51ASX

9 Cable Tie, Nylon, 11.5” Lg. 12 108578

10 Inlet Hose Assembly, Back Mount 1 179383

11 Outlet Hose Assembly, Back Mount 1 179401

12 Tube Support Bracket, Back Mount 2 179411

13 #10 Spacer, 1/4” Lg. 4 600856-22L

14 Flat Head Screw, Phillips, #10-32 UNC-2A x 1.00” Lg. 4 179438-Q01

15 Self-tapping Screw, 1/4-20 x .50” Lg. 8 601741-65B

16 Tube Assembly, Side Mount 2 179442

17 Tube Support Bracket, with Grommet, Side Mount 4 179453

Summary of content (6 pages)

PAGE 1
Panel Mount Kit for LiquiFlo AC Drives M/N 41L4060 Model Number 41L4060PM Instruction Manual D2-3460 ! ATTENTION: Only qualified personnel familiar with the construction and operation of this equipment and the hazards involved should install, adjust, operate, and/or service this equipment. Read and understand this instruction manual in its entirety before proceeding. Failure to observe this precaution could result in severe bodily injury or loss of life.
PAGE 2
Installing the Panel Mount Kit ATTENTION: The drive is at line voltage when connected to incoming AC power. Disconnect, tag, and lockout all incoming power to the drive before performing the following procedure. Failure to observe this precaution could result in severe bodily injury or loss of life. ! ATTENTION: The user is responsible for conforming with all applicable local, national, and international codes. Failure to observe this precaution could result in damage to, or destruction of, the equipment.
PAGE 3
Step 3. Install the insulation (item 8) over each of the three output power leads (see figure 1). After tightening the pressure lugs, fasten the insulation in place using two cable ties per lead (item 9). Installing the Coolant Input and Output Hoses Coolant input and output hoses can be routed either through the back of the cabinet or through the side of the cabinet. Procedures for both methods follow. To route the coolant hoses through the back of the cabinet: Step 1. Drill the two 3.
PAGE 4
Panel Mount Kit for LiquiFlo AC Drives M/N 41L4060
PAGE 5
PAGE 6
U.S. Drives Technical Support Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: support@drives.ra.rockwell.com, Online: www.ab.com/support/abdrives Trademarks not belonging to Rockwell Automation are property of their respective companies. Publication D2-3460-August 2000 Copyright © 2000 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.