Owner's manual

ManualsBrandsRockwell Automation ManualsEquipmentLiqui-Flo V2.0 AC Drive

Table Of Contents

Front Cover
Important User Information
Summary of Changes
- New and Updated Information
Table of Contents
Introduction
- Firmware Versions
- Manual Conventions
- Getting Assistance from Rockwell Automation
- Additional Resources
About the Drive
- Identifying the Drive by Cabinet Assembly ID Number
- LiquiFlo 2.0 Drive Component Locations
- Identifying the Power Module by Model Number
- AC Line I/O Board Description (Frame 3 Only)
- Standard I/O Board Description (Frame 3 Only)
- Combined I/O Board Description (Frame 4 Only)
- DPI Communication Ports
- Optional Equipment
Planning the Installation
- General Requirements for the Installation Site
- Wiring Requirements for the Drive
  - Determining Wire Size Requirements
  - Verifying Power Module Output Current Rating Is Greater Than Chiller Running Load Amps
- Stopping the Drive
Mounting The Power Module and Grounding the Drive
- Lifting and Mounting the Drive
- Grounding the Drive
- Lifting and Mounting the Power Module
Installing Input and Output Power Wiring
- Installing Power Wiring from the AC Input Line to the Main Input Circuit Breaker
- Installing Wiring from the Power Module Output Terminals to the Motor
Completing the Installation
- Checking the Installation
- Powering Up After Installation Is Complete
Using the Start-up Routines
- Preparing for Startup
- Running the Start-up Routines
- Exiting Before Completing the Start-Up Routines
Programming Basics
- About Parameters
- How Parameters are Organized
- Inverter Parameters View
- Rectifier Parameters View
- Accessing the Parameters
  - Viewing Rectifier or Inverter Parameters
- Selecting the Parameter Access Level
  - Inverter Parameters Basic Access Level
  - Rectifier Parameters Basic Access Level
- Security and Passwords
  - If There is More Than One OIM Connected to the Drive
Parameter Descriptions
- What the Symbols Mean
- Parameter Organization
- Inverter Parameters
- Rectifier Parameters
Troubleshooting the Drive
- Verify that the DC Bus Capacitors are Discharged Before Servicing the Drive
- Determining Drive Status Using the Status LEDs
- About Alarms
  - Alarm Descriptions
- About Faults
- Diagnostic Parameters
- Common Symptoms and Corrective Actions
- Replacement Parts
- Board Replacement, Firmware Setup Procedures
- Troubleshooting the Drive Using the OIM
- Checking the Power Modules with Input Power Off
  - Contacting Technical Support for Assistance
Technical Specifications
- Service Conditions
- Environmental Conditions
- Cooling System Specifications (Refrigerant)
- Motor Overload Protection
Using the OIM
- Installing and Removing the OIM
  - Removing the OIM While the Drive is Powered
- Display Description
  - Key Descriptions
- OIM Menu Structure
- Powering Up and Adjusting the OIM
- Selecting a Device in the System
- Using the OIM to Program the Drive
  - Viewing and Adjusting Parameters
  - Loading and Saving User Sets
- Monitoring the Drive Using the Process Display Screen on the OIM
- Displaying and Changing the OIM Reference
- Customizing the Process Display Screen
- Customizing the Function Keys
- Controlling the Drive From the OIM
  - Starting the Drive
  - Stopping the Drive
LiquiFlo 2.0 Drive Frame 3 Wiring Diagrams
- Frame 3 Wiring Diagrams
LiquiFlo 2.0 Drive Frame 4 Wiring Diagrams
- Frame 4 Wiring Diagrams
Index
Back Cover

Rockwell Automation Publication D2-3518-3 - May 2013 45

Chapter 4

Mounting The Power Module and Grounding the

Drive

This chapter shows how to mount and properly ground the drive.

Lifting and Mounting the

Drive

Be careful to prevent damage due to dropping or jolting when moving the drive.

A forklift truck or similar means of lifting and transporting may be used. Sling in

a manner that equalizes the load at the lifting points. Use a spreader bar if the

angle of the sling is less than 45 degrees relative to horizontal. Do not jolt while

lifting.

Figure 19 - Lift Point Locations for LiquiFlo 2.0 Drives (Frame 3)

Lifting Points