Owner manual

Item Number 814036 - Rev C
2-18 Installation
9. Position the slide over the complete sections and continue aligning the
remainder of the plates.
10. If the area where the magnet plates are to be installed does not allow you
to use a straight edge describes above, an alternate method of aligning
plates can be done. Space the plate by using a 0.020 plastic shim between
the magnet plates, tighten the bolts, and then remove the shim.
11. Once all the alignment is completed, torque all bolts to values listed in
the tables.When considering torque values for mounting hardware, take
into account the magnet plate, mounting surface and mounting
hardware. Per Table 2.N secure all assemblies in place using all
mounting holes.
ATTENTION
!
Remove alignment tool and make certain all magnet plate
mounting hardware is flush or below magnet surface to
prevent damage to the coil.
Table 2.N Recommended Seating Torques (Inch-Lb.) for Application in Various Materials
1960 Series Socket Head Cap Bolts (ANSI B18.3)
(1)
Bolt
Size
Mild Steel Rb 87
(2)
Cast Iron Rb 83
Brass Rb 72
(3)
Aluminum Rb 72
(4)
(2024-T
4
)
UNC UNF UNC UNF UNC UNF
Plain
Cadmium
Plated
Plain
Cadmium
Plated
Plain
Cadmium
Plated
Plain
Cadmium
Plated
Plain
Cadmium
Plated
Plain
Cadmium
Plated
#0 - - 2.1* 1.6* - - 2.1* 1.6* - - 2.1* 1.6*
#1 3.8* 4.7* 4.1* 3.0* 3.8* 2.9* 4.1* 3.0* 3.8* 2.9* 4.1* 3.0*
#2 6.3* 4.7* 6.8* 5.1* 6.3* 4.7* 6.8* 5.1* 6.3* 4.7* 6.8* 5.1*
#3 9.6* 7.2* 10.3* 7.7* 9.6* 7.2* 10.3* 7.7* 9.6* 7.2* 10.3* 7.7*
#4 13.5* 10* 14.8* 11* 13.5* 10* 14.8* 11* 13.5* 10* 14.8* 11*
#5 20* 15* 21* 16* 20* 15* 21* 16* 20* 15* 21* 16*
#6 25* 19* 28* 21* 25* 19* 28* 21* 25* 19* 28* 21*
#8 46* 34* 48* 36* 46* 34* 48* 36* 46* 34* 48* 36*
#10 67* 50* 76* 57* 67* 50* 76* 57* 67* 50* 76* 57*
1/4 158* 119* 180* 136* 136 102 136 102 113 85 113 85
5/16 326* 245* 360* 270* 228 171 228 171 190 143 190 143
3/8 580* 435* 635 476 476 357 476 357 397 298 397 298
7/16 930* 698* 1,040* 780* 680 510 680 510 570 425 570 425
1/2 1,0420* 1,530* 2,250 1,690 1,690 1,270 1,690 1,270 1,410 1,060 1,410 1,060
(1)
All bolts must meet the specified grade or better.
(2)
Torques based on 80,000 psi bearing stress under head of bolt.
(3)
Torques based on 60,000 psi bearing stress under head of bolt.
(4)
Torques based on 50,000 psi bearing stress under head of bolt.
* Denotes torques based on 100,00 psi tensile stress in bolt threads up to 1” diameter.
To convert inch-pounds to inch-ounces, multiply by 16.
To convert inch-pounds to foot-pounds, divide by 12.