User Manual

B-6 AutoMax Network Communication Option Board for the GV3000/SE AC Drive
P.062, Option Port: Comm Loss Response 1 29 1 62
P.063, Option Port: Network Ref Source 1 30 0 to 7 1 63 0 to 7
P.064, Option Port: Netw Trim Ref Source 1 30 8 to 15 1 63 8 to 15
P.065, Option Port: Type and Version 2 31 n/a
P.066, Network Output Register 1 Source 2 3 0 to 7 2 45 0 to 7
P.067, Network Output Register 2 Source 2 3 8 to 15 2 45 8 to 15
P.068, Network Output Register 3 Source 2 4 0 to 7 2 46 0 to 7
P.069, Network Output Register 4 Source 2 4 8 to 15 2 46 8 to 15
P.090, Diagnostics Source n/a n/a
P.091, Diagnostics Display n/a n/a
P.095, Power Module Output Amps 3, V/Hz 27 n/a
P.098, Software Version Number 1 31 n/a
P.099, Power Module Type 3 31 n/a
Parameter processing error flag 1 14 8 n/a
Power Module not identified (PUn) 1 13 10 n/a
Power Module Output Amps (P.095) 3, V/Hz 27 n/a
Power Module Type (P.099) 3 31 n/a
Programming Disable (P.051) n/a n/a
PUc (missing Power Module ID connector) 1 13 9 n/a
PUn (Power Module not identified) 1 13 10 n/a
PUo (drive power electronic overload) 1 13 6 n/a
Restore Defaults (P.050) n/a n/a
RMI (r.) parameters n/a n/a
Rotor Time Constant (U.021) 3, Vector 17 3, Vector 46
Run/jog status 1 0 3 n/a
Run/jog select n/a 1 32 3
S-Curve Enable (P.019) 2 11 2 39
Selected speed reference value 1 1 n/a
Self-tuning status (SF) 1 12 12 n/a
Sequencing control word n/a 1 32
Slip Compensation (H.004) 3, V/Hz 4 3, V/Hz 36
Software Version Number (P.098) 1 31 n/a
Speed Display Scaling (P.028) 2 18 1 52
Speed feedback 1 3 n/a
Speed reference sum 1 2 n/a
Speed regulation select n/a 1 32 7
Speed Regulator Integral Gain (U.013) 1 25 1 48
Speed Regulator Prop Gain (U.012) 1 24 1 47
Spurious host PC comm interrupt (UAr) 1 12 11 n/a
SrL (comm loss between
Regulator/PC/OIM)
11210n/a
Start n/a 1 32 0
Status word 1 1 0 n/a
Status word 2 1 26 n/a
Stop n/a 1 32 1
Stop sequence in progress 1 0 5 n/a
Stop Type (P.025) 2 15 0 to 7 1 50
STOP/RESET Key Disable (P.055) 2244 2384
SVC Flux Current Regulator Gain (U.032) 3, Vector 22 3, Vector 55
SVC Slip Adjust (U.030) 3, Vector 20 3, Vector 53
SVC Sync Direction (U.031) 3, Vector 21 0 to 7 3, Vector 54 0 to 7
Description or GV3000/SE Parameter
Read Only Read/Write
Drop Register Bit Drop Register Bit