User Manual

Register Map Summary A-3
23 Draw Gain Percentage (P.016) Fault Auto Reset Time (P.044) OCL Lead/Lag Low Frequency (U.042) Reserved 24 Speed Regulator Proportional Gain
(U.012)
Encoder Loss Enable (P.039) (bit 0) Output Phase Loss Enable (P.045) (bit 1)
Manual Reference Preset Enable P.053) (bit 2) AUTO/MAN Key Disable (P.052) (bit 3) STOP/RESET Key Disable (P.055) (bit 4)
OCL Lead/Lag Ratio (U.043) Reserved
25 Speed Regulator Integral Gain (U.013) Current Compounding Gain (U.026) OCL Reference Gain (U.044) Reserved 26 Status word 2 Carrier Frequency (kHz) (P.047) OCL Proportional Gain (U.045) Reserved 27 Elapsed Time Meter (P.029) Volts/Hertz or Vector Regulation (P.048) OCL Integral Gain (U.046) Power Module Output Amps (P.095) 28 Network Connection Type (P.061) Country Defaults (P.049) Drive panel amps Drive panel amps 29
Communication Loss Response (P.062)
Inertia Compensation Gain (U.027) Drive panel volts Drive panel volts
30
Network Reference Source (P.063, P.064)
Losses Compensation Gain (U.028) OCL Trim Range Percentage (U.047) Reserved
31 Software Version (P.098) Type and Version (P.065) Power Module Type (P.099) Power Module Type (P.099) 32
Sequencing control word Reserved Encoder PPR (U.001) Motor Nameplate Volts (H.000)
33 Option port speed/torque ref Reserved
Motor Poles (U.002) Motor Nameplate Base Frequency (H.001)
34 Option port trim reference
Terminal Strip Analog Output Source (P.012)
Motor Nameplate Base Frequency (U.003) Motor Nameplate Amps (H.002)
35 Network inertia compensation
Jog Ramp Accel Time (P.021) Motor Nameplate Amps (U.004) Torque Boost Voltage (H.003)
36 Reserved
Jog Ramp Decel Time (P.022) Motor Nameplate RPM (U.005) Slip Compensation (H.004)
37
Accel Time 1 (RAMP 1) (P.001) Forward/Reverse Configuration (P.027) Magnetizing Current (U.006) DC Braking Enable (H.005)
38
Decel Time (RAMP 1) (P.002) Encoder Loss Enable (P.039) (bit 0)
Output Phase Loss Enable (P.045) (bit 1) Manual Ref. Preset Enable (P.053) (bit2)
AUTO/MAN Key Disable (P.052) (bit 3) STOP
/
RESET
Key Disable (P.055)
(bit 4)
Motor Nameplate Volts (U.007) DC Braking Start Frequency (H.006)
39
Minimum Speed (P.003)
S-Curve Enable (P.019)
(bit 4)
Torque Regulator Proportional Gain (U.014)
DC Braking Current (H.007)
40
Maximum Speed (P.004)
Motor Overload Enable (P.040)
(bit 0)
Level Sense Start Enable (P.054)
(bit 1)
Lo DC Bus Fault Avoid. Enable (U.023)
(bit 2)
Hi DC Bus Fault Avoid. Enable (U.024)
(bit 3)
OCL Proportional Trim Enable (U.048) (bit 4)
Torque Regulator Integral Gain (U.015) DC Braking Time (H.008)
41
Current Limit (P.005) Motor Overload Type (P.041) Field Weakening Start RPM (U.016) Avoidance Frequency Enable (H.009)
Table A.2 – Register Map Summary (Continued)
Reg
Description or GV3000 Parameter
Drop_1 Drop_2 Drop_3 (Vector) Drop_3 (V/Hz)