User Manual

B-4 AutoMax Network Communication Option Board
OCL TYPE3 POSN REG EN
(P.814)
3532
OIM COMM TIMEOUT (F00011) 1 10 13
OPEN ARMATURE (F00007) 1 10 7
OPEN SCR SENSITIVITY (P.600) 4 30
443
OPEN SCR TRIP THRESH (P.601) 4 31
444
Outer control loop enable 1 32 7
OVERSPEED (F00003) 1 10 9
Parameter processing error(s) 1 0 10
PLL MAXIMUM ERROR (P.308) 4 25
440
POS CURRENT LIM SEL (P.223) 2 57
POSITIVE CURRENT LIM (P.005) 1 44
25
PULSE TACH FEEDBACK (P.292) 3 1
PULSE TACH PPR (P.207) 3 22
362
PULSE TACH QUADRATURE
(P.208)
323
363
Ramp stop 1 26 4
RAMP STOP DECEL TIME (P.018) 2 33
REGULATOR SW VERSION (P.794) 131
REVERSE DISABLE (P.015) 2 17
262
Run 1 32 0
S-CURVE ROUNDING (P.014) 1 46
216
SCR # or MULTIPLE SCRS NOT
OPERATING (F00030–F00042)
11010
SELF TUNE FAULT (F00060 to
F00099
)
1103
Sequencing control word 1 32
SPD LEADLAG LOW FREQ
(P.214)
326
345
SPD LEADLAG RATIO (P.213) 3 25
344
SPD LEADLAG SELECT (P.216) 3 28
347
SPD LOOP ERROR (P.297) 3 2
SPD LOOP FEEDBACK (P.296) 1 3
Table B.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Alternate Map) (Continued)
Parameter Name (No.) Drop Register Bit
SPD LOOP LAG BYPASS (P.217) 3 29
348
SPD LOOP LAG FREQ (P.215) 3 27
346
SPD LOOP OUTPUT (P.299) 1 4
SPD LOOP PI INIT SEL 232
SPD LOOP PI INIT VAL 139
SPD LOOP PI LEAD FREQ (P.212) 1 49
29
SPD LOOP PI PROP GAIN (P.211) 1 48
28
SPD LOOP PI RESET 1326
SPD LOOP REFERENCE (P.295) 1 2
SPD SOURCE SEL OUT (P.193) 2 0
SPEED FEEDBACK GAIN 138
Stop 1 32 1
Stop asserted/Run de-asserted 1260
Stop cause word 1 26
STOP DECEL SELECT (P.122) 3 53 3
STOP MODE SELECT (P.114) 2 53
STOP SPEED THRESHOLD
(P.113)
229
250
SUSTAINED OVERLOAD (F00005) 1102
TACH LOSS SCR ANGLE (P.608) 2 43
TACHOMETER LOSS (F00002) 1 10 12
Terminal strip auto/manual 1 1 13
Terminal strip fault reset 1 1 7
Terminal strip forward/reverse 1 1 3
Terminal strip jog 1 1 4
Terminal strip run 1 1 2
Terminal strip stop 1 1 5
TOP SPEED (P.011) 2 13
261
TRIM MODE SELECT (P.110) 2 26
247
TRIM OUTPUT (P.197) 2 31
TRIM RANGE (P.109) 1 47
27
TRIM REF REGISTER (P.107) 2 24
TRIM REFERENCE SELECT
(P.108)
225
246
Table B.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Alternate Map) (Continued)
Parameter Name (No.) Drop Register Bit