User Manual

Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Alternate Map) B-3
IET (OVERCURRENT) (F00001) 1 10 8
In current limit 1 0 9
INERTIA COMP SELECT (P.221) 2 56
Internal stop request 1 26 2
IR COMPENSATION (P.206) 2 54
Jog 1 32 3
JOG ACCEL/DECEL TIME (P.013) 2 15
240
Jog de-asserted > 1 second 1 26 1
JOG SPEED 1 (P.012) 2 14
252
Last alarm 1 14
LEVEL DETECT 1 DELAY (P.604) 4 37
LEVEL DETECT 1 SELECT (P.602) 460
LEVELDETECT1THRESH (P.603) 4 36
LEVEL DETECT 2 DELAY (P.607) 4 39
LEVEL DETECT 2 SELECT (P.605) 461
LEVEL DETECT 2THRESH (P.606) 4 38
Level detector 1 output 1 0 11
Level detector 2 output 1 0 12
Main contactor opened 1 26 9
MAXIMUM CURRENT (P.007) 3 12
358
MAXIMUM SPEED (P.004) 1 43
24
Memory save 1 32 11
MINIMUM SPEED (P.003) 1 42
23
MOTOR BRUSH WEAR LOW
(A00001)
1130
MOTOR HOT FLD AMPS (P.510) 3 55
MOTOR RATED ARM AMPS
(P.008)
313
359
MOTOR RATED ARM VOLTS
(P.009)
314
360
Motor thermostat 1 1 15
MOTOR THERMOSTAT TRIP
(F00008)
1104
NEG CUR LIM INV EN (P.226) 3 53 0
NEG CURRENT LIM SEL (P.224) 2 58
Table B.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Alternate Map) (Continued)
Parameter Name (No.) Drop Register Bit
NEGATIVE CURRENT LIM (P.006) 1 45
26
NETW COMM LOSS SEL (P.901) 3 52
NETW CONNECT TYPE (P.910) 1 28
162
NETW IN REG 1 (P.905) 1 34
NETW IN REG 2 (P.906) 1 35
NETW IN REG 3 (P.907) 1 36
NETW OUT REG 1 SELECT
(P.902)
158
NETW OUT REG 2 SELECT
(P.903)
159
NETW OUT REG 3 SELECT
(P.904)
160
NETW REGISTER MAP SEL
(P.914)
129
NETW COMM TIMEOUT (F00013) 11014
Network Output Register 1 1 7
Network Output Register 2 1 8
Network Output Register 3 1 9
Network Reference 1 33
NOMINAL AC LINE FREQ (P.306) 4 23
462
NOMINAL AC LINE VOLTS (P.307) 4 63
463
NORMALIZED INERTIA (P.222) 1 57
OCL FEEDBACK SELECT (P.804) 2 60
OCL LEADLAG LOW FREQ (P.806) 238
OCL LEADLAG RATIO (P.807) 2 39
OCL LEADLAG SELECT (P.805) 2 37
OCL OUTPUT (P.848) 1 21
OCL PI LEAD FREQ (P.809) 1 53
OCL PI NEGATIVE LIMIT (P.811) 1 55
OCL PI POSITIVE LIMIT (P.810) 1 54
OCL PI PROP GAIN (P.808) 1 52
OCL PROP TRIM SELECT (P.813) 3 53 1
OCL RAMP OUTPUT (P.846) 2 11
OCL REF RAMP TIME (P.802) 2 35
OCL REF REGISTER (P.801) 2 34
OCL REF ROUNDING (P.803) 2 36
OCL REFERENCE SELECT(P.800) 2 59
OCL TRIM RANGE (P.812) 2 55
Table B.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Alternate Map) (Continued)
Parameter Name (No.) Drop Register Bit