User Manual

B-2 AutoMax Network Communication Option Board
CML FEEDBACK GAIN ADJ
(P.300)
330
349
CML PI LEAD FREQUENCY
(P.302)
151
37
CML PI PROP GAIN (P.301) 1 50
36
CML REF LIMIT SELECT (P.311) 3 53 5
CML REF RATE LIMIT (P.303) 2 51
38
CML REFERENCE (P.396) 3 3
Coast/DB interlock 1 1 6
Coast/DB interlock opened 1 26 8
Coast/DB stop 1 26 5
CONTROL SOURCE SEL (P.000) 1 15
CONTROLLER THERMOSTAT TRIP
(F00009)
1105
CURRENT COMPOUNDING
(P.209)
156
324
Current limit stop 1 26 3
Customer interlock 1 1 1
Customer interlock opened 1 26 7
DECELERATION TIME (P.002) 2 2
141
DIG IN 0 SELECT (P.428) 4 47
DIG OUT 1 CONTACT TYP
(P.410)
4500
DIG OUT 1 SELECT (P.409) 4 48
DIG OUT 2 CONTACT TYP
(P.412)
4501
DIG OUT 2 SELECT (P.411) 4 49
Digital input 0 1 1 14
Drive jogging 1 0 3
Drive ready 1 0 0
Drive running 1 0 1
Drive status word 1 1 0
Drive status word 2 1 1
Drive stopping 1 0 5
ENHANCED FLD VOLT ADJ
(P.500)
427
441
Fault active 1 0 2
Fault latch bits word 1 1 10
Fault log clear and reset 1 32 8
Table B.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Alternate Map) (Continued)
Parameter Name (No.) Drop Register Bit
Fault reset 1 32 2
Fault stop or self-tune complete 1266
FEEDBACK SELECT (P.200) 1 61
315
FIELD AUTO WEAKEN (P.517) 3 57
FIELD CURRENT LOSS (F00004) 1 10 1
FIELD ECONOMY ACTIVE (P.599) 4 29
FIELD ECONOMY DELAY (P.501) 4 28
442
FIELD ECONOMY REF (P.511) 3 33
FIELD FEEDBACK (P.589) 1 22
FIELD LOSS THRESHOLD (P.512) 3 56
FIELD PI LEAD FREQ (P.515) 3 35
FIELD PI PROP GAIN (P.514) 3 34
FIELD REF REGISTER (P.513) 1 37
FIELD REF SELECT (P.521) 3 51
FIELD REFERENCE (P.590) 3 4
First fault 1 12
FLD FEEDBACK GAIN ADJ (P.516) 3 36
FLD WEAKEN LEAD FREQ
(P.520)
339
FLD WEAKEN PROP GAIN (P.519) 3 38
FLD WEAKEN THRESHOLD
(P.518)
337
FN/DB status 1 1 0
Forward/Reverse command 1 0 4
FREQ IN (P.491) 1 20
FREQ IN FULL SCALE (P.424) 4 56
FREQ IN ZERO (P.423) 4 55
FREQ OUT FULL SCALE (P.427) 4 59
FREQ OUT SELECT (P.425) 4 57
FREQ OUT ZERO (P.426) 4 58
Fwd/Rev select 1 32 4
I/O Expansion kit digital input
1 (Preset speed select 1)
118
I/O Expansion kit digital input
2 (Preset speed select 2)
119
I/O Expansion kit digital input
3 (
MOP decrement)
1110
I/O Expansion kit digital input
4 (
MOP increment)
1111
I/O Expansion kit digital input
5 (
OCL enable)
1112
Table B.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Alternate Map) (Continued)
Parameter Name (No.) Drop Register Bit