User Manual

Cross Reference of Parameter Name to Drop and Register (FlexPak 3000 Original Map) A-3
IET (OVERCURRENT) (F00001) 1 10 8
In current limit 1 0 9
INERTIA COMP SELECT (P.221) 2 56
Internal stop request 4 22 2
IR COMPENSATION (P.206) 1 55
321
Jog 1 32 3
JOG ACCEL/DECEL TIME (P.013) 2 15
240
Jog de-asserted < 1 second 4 22 1
JOG SPEED 1 (P.012) 1 53
214
Last alarm 1 14
Level Dectector Outputs 4 21 0&1
LEVEL DETECT 1 DELAY (P.604) 4 37
LEVEL DETECT 1 SELECT (P.602) 460
LEVEL DETECT 1 THRESH (P.603) 436
LEVEL DETECT 2 DELAY (P.607) 4 39
LEVEL DETECT 2 SELECT (P.605) 461
LEVEL DETECT 2 THRESH (P.606) 438
Main contactor opened 4 22 9
MAXIMUM CURRENT (P.007) 3 12
358
MAXIMUM SPEED (P.004) 1 19
143
Memory save 1 32 11
MINIMUM SPEED (P.003) 1 18
142
MOTOR BRUSH WEAR LOW
(A00001)
1130
MOTOR HOT FLD AMPS (P.510) 3 55
MOTOR RATED ARM AMPS
(P.008)
313
359
MOTOR RATED ARM VOLTS
(P.009)
314
360
MOTOR THERMOSTAT TRIP
(F00008)
1104
NEG CURRENT LIM SEL (P.224) 2 58
NEGATIVE CURRENT LIM (P.006) 1 21
145
Table A.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Original Map) (Continued)
Parameter Name (No.) Drop Register Bit
NETW COMM LOSS SELECT
(P.901)
129
157
NETW CONNECT TYPE (P.910) 1 28
162
NETW IN REG 1 (P.905) 1 34
NETW IN REG 2 (P.906) 1 35
NETW IN REG 3 (P.907) 1 36
NETW OUT REG 1 SELECT
(P.902)
158
NETW OUT REG 2 SELECT
(P.903)
159
NETW OUT REG 3 SELECT
(P.904)
160
NETWORK COMMUNICATION
TIMEOUT (F00013)
11014
Network Output Register 1 1 7
Network Output Register 2 1 8
Network Output Register 3 1 9
Network Reference 1 33
NOMINAL AC LINE FREQ (P.306) 4 23
462
NOMINAL AC LINE VOLTS (P.307) 4 24
463
NORMALIZED INERTIA (P.222) 2 33
OCL FEEDBACK SELECT (P.804) 2 60
OCL LEADLAG LOW FREQ (P.806) 238
OCL LEADLAG RATIO (P.807) 2 39
OCL LEADLAG SELECT (P.805) 2 37
OCL OUTPUT (P.848) 1 21
212
OCL PI LEAD FREQ (P.809) 2 52
OCL PI NEGATIVE LIMIT (P.811) 2 54
OCL PI POSITIVE LIMIT (P.810) 2 53
OCL PI PROP GAIN (P.808) 2 51
OCL RAMP OUTPUT (P.846) 2 11
OCL REF RAMP TIME (P.802) 2 35
OCL REF REGISTER (P.801) 2 34
OCL REF ROUNDING (P.803) 2 36
OCL REFERENCE SELECT
(P.800)
259
OCL TRIM RANGE (P.812) 2 55
Table A.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Original Map) (Continued)
Parameter Name (No.) Drop Register Bit