User Manual

A-2 AutoMax Network Communication Option Board
AUTO MODE MIN BYPASS
(P.111)
227
248
AUTO MODE RAMP BYPASS
(P.112)
228
249
AUTO REFERENCE SELECT
(P.103)
221
354
Average
CML feedback 1 6
BLOWER MOTOR STARTER OPEN
(F00006)
1106
CML FEEDBACK GAIN ADJ
(P.300)
330
349
CML PI LEAD FREQUENCY
(P.302)
126
151
CML PI PROP GAIN (P.301) 1 25
150
CML REF RATE LIMIT (P.303) 1 27
152
CML REFERENCE (P.396) 3 3
Coast/DB interlock 1 0 10
Coast/DB interlock opened 4 22 8
Coast/DB stop 4 22 5
CONTROL SOURCE SELECT
(P.000)
115
CONTROLLER THERMOSTAT TRIP
(F00009)
1105
CURRENT COMPOUNDING
(P.209)
156
324
Current limit stop 4 22 3
Customer interlock 1 0 11
Customer interlock opened 4 22 7
DECELERATION TIME (P.002) 1 17
141
DIG OUT 1 CONTACT TYP (P.410) 4500
DIG OUT 1 SELECT (P.409) 4 48
DIG OUT 2 CONTACT TYP (P.412) 4501
DIG OUT 2 SELECT (P.411) 4 49
Drive jogging 1 0 3
Drive ready 1 0 0
Drive running 1 0 1
Drive status word 1 1 0
Table A.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Original Map) (Continued)
Parameter Name (No.) Drop Register Bit
Drive stopping 1 0 5
ENHANCED FLD VOLT ADJ
(P.500)
427
441
Fault active 1 0 2
Fault latch bits word 1 1 10
Fault log clear and reset 1 32 8
Fault reset 1 32 2
Fault stop or self-tune complete 4226
FEEDBACK SELECT (P.200) 1 61
315
FIELD AUTO WEAKEN (P.517) 3 57
FIELD CURRENT LOSS (F00004) 1 10 1
FIELD ECONOMY ACTIVE (P.599) 4 29
FIELD ECONOMY DELAY (P.501) 4 28
442
FIELD ECONOMY REF (P.511) 3 33
FIELD FEEDBACK (P.589) 1 22
35
FIELD LOSS THRESHOLD (P.512) 3 56
FIELD PI LEAD FREQ (P.515) 3 35
FIELD PI PROP GAIN (P.514) 3 34
FIELD REF REGISTER (P.513) 1 37
FIELD REFERENCE (P.590) 3 4
First fault 1 12
FLD FEEDBACK GAIN ADJ (P.516) 3 36
FLD WEAKEN LEAD FREQ
(P.520)
339
FLD WEAKEN PROP GAIN (P.519) 3 38
FLD WEAKEN THRESHOLD
(P.518)
337
Forward/reverse command 1 0 4
Forward/reverse select 1 32 4
FREQ IN (P.491) 1 20
43
FREQ IN FULL SCALE (P.424) 4 56
FREQ IN ZERO (P.423) 4 55
FREQ OUT FULL SCALE (P.427) 4 59
FREQ OUT SELECT (P.425) 4 57
FREQ OUT ZERO (P.426) 4 58
I/O Expansion kit digital inputs 4 0 0 – 4
Table A.1 – Cross Reference of Parameter Name to Drop and
Register (FlexPak 3000 Original Map) (Continued)
Parameter Name (No.) Drop Register Bit