User Manual

Programming 4-7
4.10 Parameters That Are Not Accessible Over the
AutoMax Network
These FlexPak 3000 parameters are not accessible over the AutoMax network at
any time.
* Indicates WebPak parameters. Are there other WebPak parameters? Should
we make separate sections for WebPak and FlexPak?
ANALOG MAN REFERENCE (P.192)
ANLG OUT 1 SIG TYPE (P.419)
*
ARMATURE DELTA (P.399)
*
CML ERROR (P.398)
*
CML FEEDBACK (P.397)
*
CT TURNS RATIO (P.010)
*
CURRENT COMPOUND TP (P.293)
DEVNET POLL MSG TYPE (P.913)
DIG IN 0 (P.490)
*
DRAW PERCENTAGE OUT (P.196)
*
FIELD DELTA (P.588)
*
FIELD DELTA HIGH LIM (P.587)
*
FLD CURRENT REGULATOR (P.586)
*
I/O EXPANSION KIT (P.797)
*
INV FAULT AVOID SEL (P.312)
*
IR COMPENSATION TP (P.290)
*J11
ANLG TACH VLT SCL (P.792)
*J14
ANLG TACH VLT RNG (P.793)
*J15
REGULATOR TYPE (P.799)
*J18
ARM I FB RESISTOR (P.395)
J20
FIELD LOSS DETECT (P.597)
J21
FLD SUPPLY JUMPER (P.598)
*
JOG OFF DELAY TIME (P.121)
*
JOG RAMP OUTPUT (P.294)
JOG SPEED 2 (P.017)
*
LEVEL DETECT 1 OUTPUT (P.648)
*
LEVEL DETECT 2 OUTPUT (P.649)
MANUAL REF SELECT (P.106)
METER OUT 1 GAIN ADJ (P.400)
METER OUT 1 SELECT (P.404)
METER OUT 1 ZERO ADJ (P.402)
METER OUT 2 GAIN ADJ (P.401)
METER OUT 2 SELECT (P.405)
METER OUT 2 ZERO ADJ (P.403)
MOP ACCEL TIME (P.115)
MOP DECEL TIME (P.120)
MOP OUTPUT (P.191)
MOP RESET ENABLE (P.116)
*
NETW COMM STATUS (P.908)
*
NETW DROP NUMBER (P.900)
*
NETW IN REG 1 (P.905)
*
NETW IN REG 2 (P.906)
*
NETW IN REG 3 (P.907)
*
NETW TYPE & VERSION (P.909)
NETWORK BAUD RATE (P.912)
*
NETWORK KIT (P.796)
OCL ENABLE (P.849)
OCL FEEDBACK (P.847)
OCL REFERENCE (P.845)
*
PHASE FIRE TEST DELTA (P.309)
*
PHASE FIRE TST BRIDGE (P.310)
*
POWER UNIT TYPE (P.795)
PRESET SPEED 1 (P.117)
PRESET SPEED 2 (P.118)
PRESET SPEED 3 (P.119)
PULSE TACHOMETER KIT (P.798)
*
SELF TUNE BRIDGE (P.220)
SELF TUNE FIELD RANGE (P.218)
*
SELF TUNE STABILITY (P.219)
*
SPD LOOP LAG OUTPUT (P.298)
*
SPEED RAMP INPUT TP (P.198)
*
SPEED RAMP OUTPUT (P.199)
*
TACH LEAD FLT DELAY (P.228)
*
TACH LEAD FLT THRESH (P.227)
*
TORQUE REFERENCE (P.189)
*
CNI PROG/RUN MODE (P.915)