Installation Instructions 3 Beipackinformation 14 fr Notice d’utilisation 25 en de Active Converter, 3 Way, RTD 931S-P1C2D-DC DIR 10000043401 (Version 00) 10000043401
1. General instructions WARNING • • • • Disconnect power prior to installation Installation only by Qualified personnel Follow all applicable local and national electrical codes Due to potential hazardous voltages in close proximity, use a nonconductive tool and proper PPE when adjusting the potentiometers on the front panel. Please observe that applications with high insulation voltages require sufficient space or insulation to adjoining devices.
3. Configuring the device 3.1 Tools A screwdriver with a 2.5 mm blade is required to set the device, and to connect the conductors to the terminals. 3.2 Open the device Remove the connector Press the lock lightly on both sides of the housing to unlock it (1), remove the upper part of the housing and the electronics (2). 3.3 Settings Set input and output ranges, minimum input values and measuring span via the DIP switches SW1 and SW2 according to the following tables.
3.3.
min –100º C –150 °C –200 °C Rmin 100 Ω 150 Ω 200 Ω Special range Rmin 1000 Ω 1500 Ω 2000 Ω Potimin Activating the manual fine calibration man. Cal.
Selecting the measuring span T 40K 50K 60K 70K 80K 90K 100K 110K 120K 125K 130K 140K 150K 160K 170K 180K 190K 200K 250K 300K 350K 400K 450K 500K 550K R 20 Ω 25 Ω 30 Ω 35 Ω 40 Ω 45 Ω 50 Ω 55 Ω 60 Ω 62,5 Ω 65 Ω 70 Ω 75 Ω 80 Ω 85 Ω 90 Ω 95 Ω 100 Ω 125 Ω 150 Ω 175 Ω 200 Ω 225 Ω 250 Ω 275 Ω R 200 Ω 250 Ω 300 Ω 350 Ω 400 Ω 450 Ω 500 Ω 550 Ω 600 Ω 625 Ω 650 Ω 700 Ω 750 Ω 800 Ω 850 Ω 900 Ω 950 Ω 1000 Ω 1250 Ω 1500 Ω 1750 Ω 2000 Ω 2250 Ω 2500 Ω 2750 Ω Poti 20% 25% 30% 35% 40% 45% 50% 55% 60% 62,5% 65% 70% 75% 80%
T 550K 600K 650K 700K 750K 800K 850K 900K R 275 Ω 300 Ω 325 Ω 350 Ω 375 Ω 400 Ω 425 Ω 450 Ω R 2750 Ω 3000 Ω 3250 Ω 3500 Ω 3750 Ω 4000 Ω 4250 Ω 4500 Ω Poti – – – – – – – – 1 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 SW 2 3 1 1 1 1 0 0 0 0 Selecting the output SW 2 Output 0…10 V 0…20 mA 4…20 mA 6 1 0 0 7 0 0 1 Selecting the step response time Step response slow quick (less exact measuring) 1 = on 0 = off 8 SW 2 8 1 0 4 1 1 0 0 1 1 0 0 5 1 0 1 0 1 0 1 0
3.4 Terminal assignment of the sensors Terminal assignment for 2-, 3-, 4-wires and potentiometers.
4. Mounting The signal conditioners are mounted on standard TS 35 rails. 5. The electrical connection Terminal assignment 1 input RTD + 2 input – 3 input RTD – 4 input sense + 5 not assigned 6 not assigned 7 output 0/4…20 mA 8 output 0…10 V 9 output GND 10 Supply voltage + 24 Vdc (cross-connected) 11 Supply voltage 0 V (cross-connected) 12 not assigned Connection cross-section max. 2,5 mm2 Multi-wire connection max. 1 mm2 (two wires with the same cross-section) 5.1 Technical Data Supply voltage 18 ...
17.5 Dimensions in mm Cross-connections for linking power to multiple devices GND 24 Vdc 111.4 38 92.4 73.4 6.
7. Accessories Designation Plug-In Jumper, 2-pole, yellow Plug-In Jumper, 2-pole, red Plug-In Jumper, 2-pole, blue Plug-In Jumper, 2-pole, black Cat. No. 1492-CJLJ5-2 1492-CJLJ5-2-R 1492-CJLJ5-2-B 1492-CJLJ5-2-BL Marker Cat. No.
8. A. B. C. D. WARNING UL Class 1, Division 2 Markings for selected Signal Conditioners “This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D hazardous locations or non hazardous locations only or the equivalent.” “WARNING: EXPLOSION HAZARD - Substitution of components may impair suitability for use in Class I, Division 2 environments.
1. Allgemeine Hinweise ACHTUNG Die Analogsignaltrenner der Reihe 931S-P1C2D-DC dürfen nur von qualifiziertem Fachpersonal installiert werden. Erst nach der fachgerechten Installation darf das Gerät mit Hilfsenergie versorgt werden. Während des Betriebs darf keine Bereichsumschaltung vorgenommen werden, da hierbei berührungsgefährliche Teile offen liegen.
3. Konfigurierung des Gerätes 3.1 Hilfsmittel Zum Einstellen des Gerätes und zum Anschluss der Leitungen an die Klemmen wird ein Schraubendreher mit einer Klingenbreite von 2,5 mm benötigt. 2 3.2 Gerät öffnen Stecker abziehen. Durch leichten Druck den Verschluss auf beiden Seiten des Gehäuses entriegeln (1), Gehäuseoberteil und Elektronik herausziehen (2). 1 3.
3.3.
min –100º C –150 °C –200 °C Rmin Rmin 100 Ω 1000 Ω 150 Ω 1500 Ω 200 Ω 2000 Ω Sonderbereich Potimin 4 0 0 0 0 SW 1 5 1 0 0 0 6 0 1 1 0 7 0 1 0 0 Einschalten des manuellen Feinabgleichs man. Abgl.
Auswahl der Messspanne T 40K 50K 60K 70K 80K 90K 100K 110K 120K 125K 130K 140K 150K 160K 170K 180K 190K 200K 250K 300K 350K 400K 450K 500K 550K 18 R 20 Ω 25 Ω 30 Ω 35 Ω 40 Ω 45 Ω 50 Ω 55 Ω 60 Ω 62,5 Ω 65 Ω 70 Ω 75 Ω 80 Ω 85 Ω 90 Ω 95 Ω 100 Ω 125 Ω 150 Ω 175 Ω 200 Ω 225 Ω 250 Ω 275 Ω R 200 Ω 250 Ω 300 Ω 350 Ω 400 Ω 450 Ω 500 Ω 550 Ω 600 Ω 625 Ω 650 Ω 700 Ω 750 Ω 800 Ω 850 Ω 900 Ω 950 Ω 1000 Ω 1250 Ω 1500 Ω 1750 Ω 2000 Ω 2250 Ω 2500 Ω 2750 Ω Poti 20% 25% 30% 35% 40% 45% 50% 55% 60% 62,5% 65% 70% 75% 80% 85
T 550K 600K 650K 700K 750K 800K 850K 900K R 275 Ω 300 Ω 325 Ω 350 Ω 375 Ω 400 Ω 425 Ω 450 Ω R 2750 Ω 3000 Ω 3250 Ω 3500 Ω 3750 Ω 4000 Ω 4250 Ω 4500 Ω Poti – – – – – – – – 1 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 SW 2 3 1 1 1 1 0 0 0 0 4 1 1 0 0 1 1 0 0 5 1 0 1 0 1 0 1 0 Auswahl des Ausgangs SW 2 Ausgang 0…10 V 0…20 mA 4…20 mA 6 1 0 0 7 0 0 1 Auswahl der Sprungantwortzeit Sprungantwort langsam schnell (geringe Messgenauigkeit) SW 2 8 1 0 1 = ein 0 = aus 19
3.4 Anschlussbelegung der Sensoren Anschlussbelegung für 2-, 3-, 4-Leiter und Potentiometer.
4. Montage Der Analogsignaltrenner wird auf TS 35 Normschiene aufgerastet. 5. Der elektrische Anschluss Klemmenbelegung 1 Eingang RTD + 2 Eingang Sense – 3 Eingang RTD – 4 Eingang Sense + 5 nicht belegt 6 nicht belegt 7 Ausgang 0/4…20 mA 8 Ausgang 0…10 V 9 Ausgang GND 10 Versorgungsspannung + 24 Vdc (querverbunden) 11 Versorgungsspannung 0 V (querverbunden) 12 nicht belegt Anschlussquerschnitt max. 2,5 mm2 10 11 12 7 8 9 1 2 3 4 5 6 Mehrleiteranschluss max. 1 mm2 (zwei Leiter gleichen Querschnitts) 5.
Abmessungen in mm 17,5 6.
7. Zubehör Bezeichnung Querverbindung – 2,5 N/2 gelb Querverbindung – 2,5 N/2 rot Querverbindung – 2,5 N/2 blau Querverbindung – 2,5 N/2 schwarz Best.-Nr. 1492-CJLJ5-2 1492-CJLJ5-2-R 1492-CJLJ5-2-B 1492-CJLJ5-2-BL Marker Best.-Nr.
DIR 10000043401 (Version 00) 24
1. Indications générales ATTENTION Les séparateurs de signaux analogiques de la gamme 931S-P1C2D-DC ne doivent être installés que par un personnel spécialisé et qualifié. L'équipement ne doit être alimenté en énergie auxiliaire qu'après installation dans les règles de l'art. Ne pas tenter de changer de plage pendant le fonctionnement, des pièces dangereuses par contact direct sont en effet accessibles.
3. Configuration de l'appareil 3.1 Accessoires Pour raccorder les conducteurs aux bornes il faut avoir un tournevis avec une étendue de 2,5 mm. 2 3.2 Ouvrir l'appareil Débrancher le connecteur mâle. En appuyant légèrement, déverrouiller le loquet des deux côtés (1), retirer la partie supérieure du boîtier et l'électronique. 3.
3.3.
min Rmin –100º C 100 Ω –150 °C 150 Ω –200 °C 200 Ω Plage spéciale Rmin 1000 Ω 1500 Ω 2000 Ω Potimin Activation du réglage manuel fin régl. man.
Choix de l'étendue de mesure T 40K 50K 60K 70K 80K 90K 100K 110K 120K 125K 130K 140K 150K 160K 170K 180K 190K 200K 250K 300K 350K 400K 450K 500K 550K R 20 Ω 25 Ω 30 Ω 35 Ω 40 Ω 45 Ω 50 Ω 55 Ω 60 Ω 62,5 Ω 65 Ω 70 Ω 75 Ω 80 Ω 85 Ω 90 Ω 95 Ω 100 Ω 125 Ω 150 Ω 175 Ω 200 Ω 225 Ω 250 Ω 275 Ω R 200 Ω 250 Ω 300 Ω 350 Ω 400 Ω 450 Ω 500 Ω 550 Ω 600 Ω 625 Ω 650 Ω 700 Ω 750 Ω 800 Ω 850 Ω 900 Ω 950 Ω 1000 Ω 1250 Ω 1500 Ω 1750 Ω 2000 Ω 2250 Ω 2500 Ω 2750 Ω Poti 20% 25% 30% 35% 40% 45% 50% 55% 60% 62,5% 65% 70% 75% 80%
T 550K 600K 650K 700K 750K 800K 850K 900K R 275 Ω 300 Ω 325 Ω 350 Ω 375 Ω 400 Ω 425 Ω 450 Ω R 2750 Ω 3000 Ω 3250 Ω 3500 Ω 3750 Ω 4000 Ω 4250 Ω 4500 Ω Poti – – – – – – – – 1 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 SW 2 3 1 1 1 1 0 0 0 0 Choix de la sortie SW 2 Sortie 0…10 V 0…20 mA 4…20 mA 6 1 0 0 7 0 0 1 Sélection du temps de réponse indicielle Réponse indicielle lente rapide (moindre précision de mesure) 1 = on 0 = off 30 SW 2 8 1 0 4 1 1 0 0 1 1 0 0 5 1 0 1 0 1 0 1 0
3.4 Brochage du capteur Brochage en montage 2, 3, 4 fils et potentiomètre.
4. Montage Les séparateurs sont encliquetés sur des rails de norme TS 35. 5. Le raccordement électrique Brochage 1 Entrée courant RTD + 2 Entrée courant Lecture – 3 Entrée courant RTD – 4 Entrée courant Lecture + 5 Non connectée 6 Non connectée 7 Sortie 0/4…20 mA 8 Sortie 0…10 V 9 Sortie GND 10 Alimentation + 24 Vdc (connexion transversale) 11 Alimentation 0 V (connexion transversale) 12 Non connectée Section max. de raccordement 2,5 mm2 10 11 12 7 8 9 1 2 3 4 5 6 Raccordement multifilaire max.
17.5 Dimensions en mm Connexion transversale d’alimentation en tension GND 111.4 38 92.4 73.4 6.
7. Accessoires Désignation Connexion transversale – 2,5 N/2 jaune Connexion transversale – 2,5 N/2 rouge Connexion transversale – 2,5 N/2 bleu Connexion transversale – 2,5 N/2 noir Réf. 1492-CJLJ5-2 1492-CJLJ5-2-R 1492-CJLJ5-2-B 1492-CJLJ5-2-BL Marker Réf.
DIR 10000043401 (Version 00)