Owner's manual

Error and System Messages
Appendix B
B-38
Message Description
S--CURVEOPTION NOT INSTALLED An attemptwasmadetoselectS-- CurveAcc/Dec (G47.1)when the S--Curveoptionbitwasset
tofalse. Makesureyour systemincludesthe S--Curve option.
SNOT LEGAL PROGRAMMINGAXIS NAME Thisis displayed atpower-upwhen theletter“S”isassigned to linearorrotaryaxis. Only the
spindle(s)can be AMPed with“S”as the name;itcannotbeassignedtoa programmable axis.
S OVER SPEED Aservomotoris turning atanRPMthat is greaterthan the maximumRPMallowed forthat
servo as defined in AMPby th e systeminstaller. Fordig ital spindles this error can result from
maximumRPMgearrange 1 being sethigherthan your AMPedallowedMaximumMotor
Speed.
SAVE COMPLETED Thechanges made to the currentdevice set-up have beensaved.
SCALE FACTORS MUST BE EQUAL FOR PLANE When performing circularmotion ormotionin certain cycles,keep thescale factorsforthe axes
ofthe active plane equal.
SCALINGINVALIDDURING POLAR Scalingcannotbe usedduring polarprogramming.
SEARCH ALREADY INPROGRESS Youcannotrequestasearchoperationwhile one iscurrentlyrunning. Completeorabortthe
currentsearch before attempting another search.
SEARCH MONITOR SELECT NOT ALLOWED You can notus e the online PAL searchmonitorutilitywhile the display selectfunctionsoftkeys
areactive. Leavethedisplayselectscreens(press DISPSELECT) before you try to accessthe
search monitorutility.
SEARCH REQUIRES ANACTIVE PROGRAM Anattempthasbeen made to perform asearch operationwhen noprogram was selected for
execution. Aprogrammustbeselected forautomaticexecution beforea programsearch can
be performed.
SEARCHSTRING NOT FOUND The characterorcharacterstringdesignated inthesearchoperation was notfound.
SECONDSPINDLENOT CONFIGURED For spindle 2 tobe programmable,itmustbe configured inAMP;a decodeerror.
SECONDARYAUX. WORD SAMEAS AXISNAME The secondary auxiliaryword(usuallyB)is the sameas anaxis name,causing an interpretation
conflictfor thecontrol. Thiswordand all axis namesare assignedin AMP.
SEE (MESSAGE) INPROGRAM BLOCK The programmer hasassigned asystemparameter thatgeneratesthismessage,te lling the
operatortoreadthecommentin the currentpartprogramblock. Program executionwillresume
when cycle startis pressed.
SEQUENCENUMBEROUT OF RANGE Asequence numberbeyond the range of1-99999 was programmed.
SEQUENCESTOPNUMBERFOUND A sequence stop numberhas beenactivated,andthatsequence numberhasbeen found in the
currently executing program. Executionwillstop afterthe blockcontaining the sequence
numbercorrespondingto the sequencestopnumberisexecuted. Executionwillresume when
cycle startis pressed.
SERIALCOMMUNICATIONS BUFFEROVERFLOW Aperipheral device communication error(such asa tape reader). The512 characterinput
(receive)bufferhasoverflowed. Datamayhave beenlost. Checkyourconfigured
communications protocol(flowcontrol)and check forpropercabling/pinconnections.
SERIAL COMMUNICATIONS ERROR #1 Thisis aninternalsoftwareerror. The controlisunable to access DF1Driver.
SERIAL COMMUNICATIONS ERROR #2 Thisis aninternalsoftwareerror. Checkcablesand tryagain.
SERIAL COMMUNICATIONS ERROR #3 Thisis aninternalsoftwareerror. Thisis anunknownDF1 Drivererror.
SERIAL COMMUNICATIONS ERROR #4 Thisis aninternalsoftwareerror. The controlisunable to access the serialcommunications
port.;check cables andtry again.
SERIAL COMMUNICATIONS ERROR #5 Serial communicationsporthasnotreceived the expectedresponsein the timeallowed.
SERIAL COMMUNICATIONS FRAMING ERROR Anincorrectnumberofbits was encounteredduringa read operation. Checkyourdevicesetup.
SERIAL COMMUNICATIONS PARITY ERROR Incorrectparity ofdata wasreceived. Check yourdevicesetup.
SERIAL PORTIN USE This message will appearifa serial communicationsportisbusywhen checked prior to
transmission.
SERIAL UART BUFFER OVERFLOW The 2characterbufferontheUART receiverhasoverflowed. A characterhasbeen lost. Check
communications setup.