Owner's manual

Error and System Messages
Appendix B
B-30
Message Description
NO PROGRAM TO RESTART There isno programto restart. The previous programwaseithercompletedorcancelled.
NO RECIPROCATION DISTANCE Areciprocationinterval ofzero (0) wasprogrammed foragrinderreciprocation fixed cycle.
NO RECIPROCATION FEEDRATE T he reciprocation feedrate,E-word,required duringa grinder reciprocationfixed cycle wasnot
programmed.
NO SPINDLE ASSIGNED TO THIS PROCESS A process attemptedto activatevirtualorcylindricalmode and that processhas nospindle
assignedtoitviaAMP.
NO STRING INPUT A programsearch operationwasrequested andno stringtosearch for has beenentered. Key
intherequired search string,andpressthe [TRANSMIT]keytoenter asearch string.
NOTOOL GROUP PROGRAMMED Ablockthatloads data into the tool managementtable doesnotcontain the parameter that
determinesthe tool group numbercorresponding to the other data in the block. The group
numberisprogrammed usingtheP-word.
NOTOOL NUMBER PROGRAMMED Ablockthatloadsdata into the tool managementtable doesnotcontain the parameterthat
determinesthe tool number corresponding to the otherdatain the block. The toolnumberis
programmed usingtheT-word.
NO UNEXPIRED T OOL AV AILABLE A requestfor a tool group wasmade,andall ofthetoolsinthattool managementgroup have
expired theirtoollives. Eitherresetthe toollifeforthe tools,orinstallnew tooling.
NON_CONSECUTIVE/TOO MANY FITTED AXES More than the allowable numberofaxes may havebeen assigned inAMPoran unfittedaxis
wasassignedbetweentwo fitted axes. Youcan assign onlyfitted axesconsecutivelyin AMP.
NON-LINEAR AXIS IN PLANEDEFINITION Thecurrentaxisplane isillegal becausea non-linearaxis(rotary)has beenassigned tothe
planein AMP.
NOT ALIGNED During the power--up alignmentprocedure,eitherthe 1326motor(connected to a9/440HR) is
misaligned orthe SINCOSdevice’smemory is corrupt.
NOT ALLOWED IN ANGLEDWHEEL MODE The axescan notbemoving whenyou changetoangledwheel mode. Also the axesinvolvedin
angledwheel motionmust be homedbefore youcanenterangledwheel mode. Otherfeatures,
suchas block retrace orjogretractalsomustnotbe active whenchangingmode.
NOT ALLOWED-G41/G42ACTIVE Anattemptwasmadetoperformsome operationorprogramsome feature thatcannotbe
performed whencuttercompensationorTT RC is active (G41 orG42). Cancelcompensationby
programming aG40 blockbefore performingtheoperation.
NOT ALLOWED FROMMDI Certain programmingcommands are notallowed fromMDI(GOTO,WHILE,etc.).
NOT ALLOWED ONDUAL/SLAVE AXIS A G26was programmedon adueled axis. The G26featureisincompatiblewith the dualaxis
feature.
NOT ALLOWED -THREADINGACTIVE Anattemptwasmadetoperformsome operation(typicallya spindle speedadjustment)thatis
notallowedwhencutting a thread. Thisincludesallformsofthreading,including singlepassor
multiplepassthreads.
NOT ING10L3 MODE AG11 blockwasprogrammedthatcancels G10L3 data settingwhen the control isnotinthe
G10L3 data setting mode. G10L3is used to setthe tool managementtable data.
NUMBER I SOUT OF RANGE Anattemptwas madeto performacalculation using the paramacrofeaturesorthe calculator
featuresthatcontainsanumberlongerthan 11 characters.
NUMBEROF MOTORS/SPINDLECONFIG ERROR Thisiserrorindicates AMP is incorrectlyconfigured forthe9/Serieshardware. Typical AMP
configuration errors thatgenerate this errorinclude:
Youhave AMPedmoremotorsthanthe currenthardware supports.
Youhave indicatedthere areservo motorsattachedtoservoboardsthatdon’texist(the
9/230 and 9/440 are configured asiftheyhaveonly oneservo card).
Youhave configuredtoomanyspindles(1on 9/230,2on 9/260 and 9/440,3on 9/290).
Too few axeswere configuredforthe indicatednumberofmotorson theboardsor
too few servos were configuredfor indicatednumberofmotors ontheboards.
NUMERIC VALUEMISSING The numeric value associatedwith the programmed word ismissing. There isan AMP
parameterthatdetermineswhether a missing numericisassumedtobe zero orifitwillgenerate
this error.