Owner's manual

Error and System Messages
Appendix B
B-29
Message Description
N
NEED SHADOW RAMFOR ONLINE SEARCH Yoursystemcontains the DH+moduleand you have notinstalled the extra RAM SIMMSthat
arerequired to run the PAL online search monitorwiththeDH+ moduleinstalled. Youmustbuy
additional RAM fora systemequipped with both ofthese features. Contactyour Allen-Bradley
Salesrepresentativetopurchasethese SIMMS. Refertoyour9/Seriesintegration manual for
detailson installing additional SIMMS.
NEED SPI NDLE FEEDBACK You attempted to usethesolid--tapping feature orsynchronization feature with aspindlethat
doesnothave feedback.
NEGATIVE DWELL VALUE Anattemptwas made to execute adwellwitha negativevalue. Dwellvaluesmustbepositive
values.
NEGATIVEF-WORD PROGRAMMED A negative feedrate wasprogrammedina programblock. Negative feedratesareillegal.
NEGATIVETO UNSIGNED LONG ERROR Internalmath errorhasoccurred;contactAllen-Bradley customersupportservices.
NEGATIVE VALUENOTALLOWED The minus (-)signwasused foran address which cannotbeprogrammedwith anegative value.
NET CORRECTIONISNOT ZERO Fora rotary axis,thenetamountofcorrectionforaxiscalibrationshouldbe zero forone
completerevolution.
NET PICK/PLUNGEAWAYFROM ENDPOINT The primaryandsecondarypick/plunge amounts, when addedtogether,are in the direction
awayfromtheprogrammedendpoint.
NETWORK COMMUNICATION DISABLED When editing or restoring communicationsconfiguration data,this message isdisplayed.
NETWORK PASSTHRU COMMUNICATIONS FAULT A communication errorhasoccurred betweenthecontrols ethernetmoduleand the ODS
passthroughdevice (typicallya PLC).
NEVER OPENED THE PROGRAM Anattemptwasmadetoeditaprogram thatwasnotcurrentlyopen.
NEW TOOL OFFSET SETUP BUT NOT ACTIVATED T he tool offsets fortheactive tool were changed,butnot activated in the currentblock. These
newtooloffsetswillnotbe activated until theset-up blocksare cleared ofthe oldtooloffsetsand
refilledwith the new tool offsets.
NO ACTIVE PROCESS CONFIGURED The AMPhas been loadedintoa multi-processing systemthathas no processes configured as
active.
NO ACTIVE PROGRAM An attemptwasmadetodo asearchwhen no partprogramisactive.
NO AXIS CONFIGURED Thecurrentactiveversion ofAMPdoes nothaveanyaxes configuredasusable. All axesare
configuredas unfitted.
NO CHARACTERS ENTEREDFOR SYMBOL You have used incorrectsearchstringsyntax inthe PAL searchmonitorutility.
NO DEPTH PROBETRIP AG26 blockreached its programmed endpoint withoutthe adaptivedepthprobebeing tripped.
The partsurface was notdetectedby the adaptivedepthprobebefore the G26blockcompleted.
NO FEEDRATE PROGRAMMED Acommand foraxismotion wasexecuted whenthere wasno activefeedrate. Appliesto
non-rapid moves (G01,G02,orG03).
NO FURTHER RETRACEALLOWED The controlhas reached ablockduringretracefrom which nofurtherretrace ispermitted.
NO INTERSECTION EXI STS Thereis no mathematicalintersection for theQPPblocksas programmed.
NO MARKER FOUND ON : The encodermarker was notdetectedwhen homing theindicated axis. Homing was
unsuccessful.
NO MOREMDIBLOCKS Cycle startwasrequested during MDImode whenthere were noMDIblocks presenttobe
executed.
NO MORE MDIBLOCKS TO RESET Aresetwasrequested duringMDImode whenthere were noincomplete or unexecutedMDI
blocks re set.
NO OFFSET ACTIVE An offsetmustbe activebefore the controlwillallowtheoffsettobe changed. This check is
usedso thatthecontrol willno the method and directionoftheoffset will bethesameas the
previous offset.
NO OPTIONAL FB PORT ON ANALOG SERVO T he system wasincorrectlyAMPed with optionalfeedbackmoduleon ananalog servo module.