Owner's manual

Error and System Messages
Appendix B
B-27
Message Description
MISSINGI/ORING DEVICE The I/Oassignmentfile thatwas compiledand downloadedwith PALdefinesan I/O ring device
that is notphysicallypresentinthe I/O ring. Verifythatalldeviceaddresssettingsarecorrect.
MISSINGINTEGRAND/RADIUS WORD Acircularorhelicalblockhas beenprogrammedwith axisdata and no radius (R) or integrand (I,
J,orK)values. Aradiusorintegrand mustbeprogrammedin acircularorhelicalblockto
define the location ofthearccenter.
MISSING KEYBOARD ANDHPG FROM I/O RING T he I/Oassignmentfilethatwas compiled anddownloadedwith PAL definesa keyboard andan
HPGthatis notphysicallypresentintheI/O ring. Alsoverify thatthe keyboard andHPG
address settingsarecorrect.
MISSING KEYBOARD FROM I/O RING The I/Oassignmentfilethatwas compiled anddownloadedwith PAL definesa keyboard thatis
notphysically presentintheI/O ring. Verify thatthe keyboard address settings are correct.
MISSINGL-WORD The L-word parameteris missingfromtheG88.5orG88.6hemisphericalpocketprogramming
block.
MISSING M02 OR M30 The controlhas executedthrough to the lastblock ofaprogramandhas notread an
end-of-programcommand (M02orM30).
MISSING MASTER AXISNAME Slave axes thatdo nothavea masterhavebeen configured fora dualgroup.
MISSING OR ILLEGAL L-VALUE Anattemptwasmadetoprograman irregularpocketmilling cycle (G89)with a missing orillegal
L-word.
MISSING PROGRAM NAME An operation,such asa copyorrename,was performedwithouttheproperprogramnames
beingspecified. The properformatconsistsofthe programperforming the operationfollowed by
a commaand the targetprogram(OLDPROGRAMNAME,NEW PROGRAMNAME).
MISSING PROGRAM NUMBER (P) Nosub-programnamewas specified ina blockthatcallsa sub-programorparamacro. A
sub-rogramname mustbe programmed with a P-word in the calling block.
MISSING PROMPT DATA The controliswaiting fordatatobe enteredon the inputline (line 2oftheCRT) using the keys
on the operatorpanel.
MISSINGQ-WORD The Q-word parameteris missingfromtheG88 orG89programmingblock.
MISSINGQ PP ANGLEWORD The secondblockofa two block QPPsetdoesnotcontain the necessaryangle word to define
an intersectionwith the firstblock.
MISSINGROUGHINGCYCLE (P/Q)WORD Aroughing cycle block wasprogrammedthatdoesnotcontain both a startingand ending
sequencenumberfor the contourblocksasprogrammedwith the P-andQ-words.
MISSINGROUGHINGCYCLE DEPTH(D)WORD A roughing cycleblockwas programmed that does notcontain the Dparameterfor depthofcut.
MISSING SHADOW RAM Eitheryour9/290 controlismissing the SIMMS necessaryforshadow RAM,oryour9/260
control is notequippedwithenough RAM to operateproperly. Ifyour9/260systemcontains
boththeDH+ module and the search monitorutility,additionalRAMmustbe installed. All 9/290
controlsmusthavethis additionalRAM. Refer toyour9/Seriesinstallationand maintenance
manualfordetails oninstallingSIMMS.
MISSINGSLAVE INCREMENTAL AXISNAME Whenusing dual axeson Lathe A,all slave axesmusthave incremental axis names.
MISSING START PARENTHESIS An erroroccurredin G05 DH+ communications blocks.
MISSING TOOL ENTRY Thisis missinga tool entry.
MODULE(S)WITH INCONSISTENT REVISI ON LEVEL Retry theupdateutility.Ifthis doesnotwork,callAllen-Bradleyand requesta newupdateutility
that matches yourhardwarerevision level.
MODULE(S)WITH INVALIDCHECKSUM Retryupdate.
MOTIONIN DWELL BLOCK An attemptwasmadetoprogram axis motioninthesameblock thatgeneratesa dwell. Noaxis
words canbe programmed ina block thatgenerates adwell.
MOTION NOT ALLOWED The blockincludesG-codes thatmustbeprogrammedin a blockwithoutaxismotion. For
example,theG-codesthatconvertfrominchtometricormetricto inchcannothave axis motion
inthesameblock.
MOTORSHAFT -LEAD SCREWRATIO TOO HIGH The motorshafttolead screwgearratio istoo hightoachievetherapidspeed assigned inAMP.