Owner's manual

Error and System Messages
Appendix B
B-26
Message Description
MINIMUMRPMLIMIT AUXILIARYSPINDLE 2 The commandedaux spindle 2speed requestedby the controlislessthantheAMPed minimum
auxspindle 2 speedforthe currentgearbeingused. Thisrequires agearchange operationora
changein the programmed auxspindle2 speed. Insomecases,the <SPINDLE SPEED
OVERRIDE> switchmay be sufficient.
MINIMUMRPMLIMIT AUXILIARYSPINDLE 3 The commandedaux spindle 3speed requestedby the controlislessthantheAMPed minimum
auxspindle 3 speedforthe currentgearbeingused. Thisrequires agearchange operationora
changein the programmed auxspindle3 speed. Insomecases,the <SPINDLE SPEED
OVERRIDE> switchmay be sufficient.
MINI MUM RPMLIMIT FIRST SPINDLE The commandedspindle 1 speedrequested bythecontrol is lessthan the AMPed minimum
spindle1 speedfor the currentgearbeingused. This requiresa gearchangeoperation ora
changein the programmed spindle 1speed. In some cases,the <SPINDLESPEED
OVERRIDE> switchmay be sufficient.
MINIMUM RPM LIMIT PRIMARY SPINDLE The commanded primary spindle speedrequested bythecontrolis less than the AMPed
minimumprimaryspindlespeed forthe currentgearbeing used. Thisrequires agearchange
operationor a changein the programmed primary spindle speed. Insomecases,the
<SPINDLE SPEED OVERRIDE> switch may be sufficient.
MINI MUM RPMLIMIT SECOND SPINDLE T he commanded spindle 2speed requestedby the control islessthantheAMPed minimum
spindle2 speedfor the currentgearbeingused. This requiresa gearchangeoperation ora
changein the programmed spindle 2speed. In some cases,the <SPINDLESPEED
OVERRIDE> switchmay be sufficient.
MINIMUMRPMLIMIT THIRDSPINDLE T he commanded spindle 3speed requestedby the control islessthantheAMPed minimum
spindle3 speedfor the currentgearbeingused. This requiresa gearchangeoperation ora
changein the programmed spindle 3speed. In some cases,the <SPINDLESPEED
OVERRIDE> switchmay be sufficient.
MIRROR NOT ALLOWED ON ROLLOVER AXIS Youcannotperformmirrored motionusingan axiswith rollover.
MISSING1394 I/ORING ADDR This message indicatesthata 1394amplifierIDhasbeen AMPedbutnotdefinedinI/O ring
assignmentfromODS. The 1394 amplifiermustbea defined device onthe9/Seriesfiberoptic
I/O ring.
MISSING( [)AFTER FUNCTION NAME Paramacro and calculatorfunctionsmusthave theirvalues enclosed in [], for example,SIN[5].
MISSING ( ]) Paramacro and calculator functions musthave theirvaluesenclosedin[],forexample,SIN[5].
The controlhasfoundthatarightbracket“]” is missingin the currentoperation.
MISSING(END)COMMAND The controlhas found anend-of-programblock(M02 orM30)beforeithas read the END
command fora paramacro DOloop.
MISSING (F) ININVERSE TIME AnF-word mustbe programmed inevery motionblock thatisnotrapid whenin inverse time
feed mode(G93). F is notmodal inG93.
MISSING(GOTO) COMMAND AnIFparamacrocondition doesnothave aGOTOwith a sequence number following the
condition.
MISSINGA (DO)COMMAND A WHILEparamacrocondition doesnothave aDOwitha loop identifier followingthe condition.
MISSING ADAPTIVEFEED DATA An attemptwasmadetocreate atransferline part programfromthe quickviewscreen with
incompleteadaptive feedrate data.
MISSING COMMA An erroroccurredin G05 DH+communications block.
MISSING COMMAOR RIGHT PARENTHESIS Anerror occurred inG05 DH+communications block.
MISSINGCUTTER COMPCODE Cuttercompensation mustbe activatedbefore initiating a G89 irregularpocketcycle.
MISSING DATAFROM BLOCK G89 irregularpocketcycleparameters aremissing froma the G89 programmingblock.
MISSING END PARENTHESIS An erroroccurred in G05 DH+ communicationsblock.
MISSING G67 Anactive modal macro (G66 orG66.1)was notcanceled by aG67 before thecontrol read an
M02orM30end-of-programcommand.
MISSINGHPG FROM I/O RING The I/Oassignmentfile thatwas compiledand downloadedwith PALdefinesan HPG thatisnot
physically presentin theI/O ring. Verify thatthe HPGaddress settingsarecorrect.