Owner's manual

Error and System Messages
Appendix B
B-23
Message Description
INVALID TOOL LENGTH OFFSET NUMBER Anattemptwasmadeto enter atoollength offsetnumberin the tool lifemanagementtablethat
islargerthan the maximumoffsetnumberallowed. Ifthe tables are being loadedby aG10
program,the length offsetnumberisentered with aH-word inthe block.
INVALID TOOL LIF E TYPE Anattemptwasmadeto enteraninvalidtool life typeforatoolgroupin the tool management
tables. Validtoollife types are type 0,1,or2.
INVALID TOOL NUMBER Eitherno tooloran invalid tool numberwas programmed in a randomtoolG10.1 block. Tools
shouldbe programmed witha Q-word in aG10.1blockor within a range determined bythe
systeminstallerinAMP. An invalidtoolnumberwasentered into the tool managementtables or
wasprogrammedin a partprogramblock.
INVALID TOOL NUMBER FROM PAL T he PAL offsetchange feature specified an invalid tool number to the control.
INVALID TOOL ORIENTATION This is aninvalidtoolorientation.
INVALID TOOL T ABLETYPE This isaninvalidtooltable type.
INVALIDVALUE ZONE3 Azone3 valuewasentered that is outsideofthezone 3limits.
INVALIDVALUE ZONE3: Thezone listedhas valuesthatareoutsideofthe zonelimits.
INVALID VELOCITY FDBK TYPE AMPfor your digitaldrivesystemhasbeen configuredforan invalid velocityloop hardware type.
Valid values fordigitalsystems areNO FEEDBACK, ABSOLUTE FEEDBACK, and
INCENCODERON DIGITAL MODULE. Otherselections areinv alid on digita l systems.
INVALID WHEEL ANGLE An invalidwheel anglehasbeen entered forthe angledwheel grinder. Wheelanglesmustbe
entered between 0 and 180 degrees. Alsowheelanglesthatapproach 90degreesarealso
invalid.
INVALID WORD IN G10L3MODE An attemptwasmadetoassigna parameterthatisnota legalparameterinthe G10L3 mode.
G10L3 assigns data tothetoolmanagementtables.
INVALIDWORDING11BLOCK An invalid word was programmed ina G11 blockthatcancelsthedatasetting mode forthetool
managementtables. The G11 codemustbeprogrammed ina blockthatcontainsno otherdata.
INVALID ZONE LIMIT This isan invalid Zone Limit.
INVALID ’,’WORD Awordotherthan achamferingC-word,a radiusR-word,orQPPangle wordwas programmed
ina block witha comma“,”. Only the radius andchamferwordscanbe preceded with a“,”ina
block.
IPDANDG16.3/G16.4CANNOT BECONCURRENT This errormessage isissuedwhen in-process dressing is onand ablockcontaining a G16.3or
G16.4 isactivatedon acylindrical grinderinangled wheelconfigurations.
J
JOG WILL CAUSE (+)OVERTRAVEL An attemptwas made to executean incremental jogthatwould move the indicatedaxis beyond
itspositive software overtravel limit.
JOG WILL CAUSE (-)OVERTRAVEL Anattemptwasmadetoexecute anincrementaljog thatwouldmovetheindicated axis beyond
its negative softwareovertravellimit.
JOGGEDHOMETOO FAST: The speedselected for the move tothehome limitswitch istoofastand thehoming operation
hasfailed. Move theaxesback to theothersideofthelimitswitch (theside before the homing
operationbegan),and re-executethehomingoperation,this timeslowingthespeed using the
<SPEED/MULTIPLY> switch or t he <FEEDRATEOVERRIDE> switch.
L
LVALUEOUTOFRANGE An L-wordrepeatcountwasprogrammedlargerthan the system is capableofperforming
(typically amaximumL of9999is permitted). Asecondblockwillneed to beprogrammedto
duplicate the commands again. Entera smallerL-wordforboth blocks.
L-WORD CANNO T BE GREATER THAN TOOL RADIUS The programmedL-word valuein a G88.5 orG88.6hemisphericalpocketcycle isgreaterthan
theprogrammedtoolradius. The incremental plungedepthofa hemisphericalpocketcycle
cannotbegreater than thetoolradius.
L-WORDOUTOFRANGE More than1000 spark-outpasseswerespecified by the L-wordin agrinderfixed cycle.