Owner's manual

Error and System Messages
Appendix B
B-14
Message Description
EXTRA KEYBOARD OR HPG ON I /O RING The controldetecteda keyboard orHPG on the 9/Series fiberoptic ring thatwasnotconfigured
asa ring device. The I/Oringwillstillfunctionand the controlwillNOT beheld in E-Stop. You
mayalsouse the keyboard or HPG byselecting it as the active device via the corresponding
PAL flags. Youshould configure the keyboard orHPGwiththe I/O assignerutility(Seeyour
9/SeriesPAL reference manual fordetails).
F
FCM DUAL PO RT RAMFAILURE The FCMdetectedan errorin dualportRAM.
FCM FLASH RAM FAILURE TheFCMdetectedanerrorinflashRAM.
FCM LOCAL RAMFAILURE The FCMdetectedan errorinlocal RAMatpower-up orduring the runtime diagnostics.
FCMPLUGCONFIGURE FAILED TheFCMcardfailedtoconfigurecorrectly.
FCMPLUGFAULT TheplugontheFCMdetectedanerror.
FCMPLUGNEGOTIATEFAILED The FCMfirmwarecouldnotcommunicatewith the plug.
FCM POWER UPSEQUENCE FAILURE Power-upfailed. Try again. If errorappears again,contactyourAllen-Bradleysales
representative.
FCM REVISION CHECKFAILURE Revisionon module isout-of-date. ContactAllen-Bradleysalesrepresentativetogetlatest
revision ofthe module’s firmware.
FCM ROMFAILURE The FCMdetectedan e rrorin ROMduring runtimediagnostics.
FCM SHADOW RAMFAILURE The FCMdetectedan errorinshadowRAM.
FCM SPURIOUSINTERRUPT A spurious interruptoccurredon the FCMcard.
FCM VRTX ERRO R A call fromVRTXfrom the FCMcard firmwarereturnedan error.
FCM WATCHDOG The watchdogon the FCMcard timedout.
FDBK NOT AVAILABLE ON 4TH AXISOF BOARD An attemptwasmade to receivefeedback fromtheaxisthatis configuredas thefourth axis ona
servo board. Youcan onlyreceive feedback fromthe firstthree axeson aservoboard.
FEEDBACK DI SCONNECTED The controlhas detecteda loss offeedback fromthe encoder. The mostlikelycauseofthis
errorwould be a broken or disconnectedwire. Axis homing will berequired afterthe error
condition iscorrected.
FEEDBACK OPTION NOT INSTALLED APTOcheckdeterminesthe legalnumberofaxes.
FEED AXISDATANOT PROGRAMMED Feed axis data required during agrinderfixed cycle wasnotprogrammed.
FEED AXISMOTION NOT ALLOWED During VirtualC programming,no axis motionisallowedon the axisspecifiedas the feed axisin
AMP.
FEED TO HARDSTOP PROGRAMMING ERROR No axis,or morethanone axis,wasprogrammedin aG24 block. Orthe programmed axis
integrandwas notprogrammed in the block.
FILECANNOT BE CONVERTED TO EIA FORMAT The filerequested to beoutputto adevice has characters thatcannotbe converted to EIA.
FILEDOWNLOAD COMPLETE Statusmessage thatmeansthedownload has completed.
FILEDO WNLOAD ERROR Checkfiledownloadand file download configurationscreensto makesure allfields are entered
correctly.
FILE DOWNLOAD INPROGRESS This status message means afileisbeing downloaded.
FIXED CYCLE ALREADY ACTIVE You cannotprograma fixed cyclewitha fixed cycle already active.
FIXEDCYCLE PROGRAMMING ERROR Afixedcycle has beenprogrammedincorrectly. Verify thatthecorrect parametershave been
usedand thatparametersrestrictedtointeger orpositivevaluesareprogrammedas such.
FLASH I NUSE -- TRYAGAIN LATER Only onetaskisallowedtowriteflashata time. Ifa secondtaskrequestsa flash write,you will
seethismessage.
FLASH SI M MS ARE NOT INSTALLED Install theflashSIMMs into the 9/Series motherboard. Flash SIMMsmustbeinstalled. Ifa
repaired systemis beinginstalled,you shouldhave savedyourflashSIMMsforre-installation
before making thereturn.