Owner's manual

Error and System Messages
Appendix B
B-9
Message Description
CPU# 2 HARDWARE ERROR#4 The 68030 main processorhasdetected anillegal address. ConsultAllen-Bradleycustomer
support services(9/290 only).
CPU# 2 HARDWARE ERROR#6 The 68030 mainprocessorhasdetecteda privilege violation. ConsultAllen-Bradleycustomer
support services(9/290 only).
CPU# 2 HARDWARE ERROR#8 CPU#2 hasdetected an unassignedvector interrupt. ConsultAllen-Bradleycustomersupport
services (9/290only).
CPU# 2 HARDWARE ERROR#9 CPU#2 hasdetected an illegalinstruction. ConsultAllen-Bradley CustomerSupportServices
(9/290 only).
CPU# 2 LOCAL RAMFAILED The RAMmemory supporting the 68030I/O ring processorhas failed(Z80I/O ring processoron
9/240 only). ConsultAllen-Bradleycustomersupportservices.
CPU# 2 PROM HAS FAILED The PROM memory supportingthe68030 (Z80 9/240 only)I/Oringprocessorhas failed its
checksumtest. ConsultAllen-Bradleycustomersupportservices.
CPU# 2 RAMHAS FAILED The RAM memory supportingthe68030 (Z80 9/240 only)I/Oringprocessorhas failed. Consult
Allen-Bradley customersupportservices.
CPU# 2 WATCHDOG ERROR The 68030(Z80 9/240only)I/O ring processorhasfailed. ConsultAllen-Bradleycustomer
support services.
CREATING BACKUPFILE -PLEASE WAIT A backup fileforthe currentutility isbeing created. The message willclear when the backup is
complete.
CREATING TOOL OFFSET FILE - PLEASE WAIT Thetooloffset table(ortables)iscurrentlybeing backed-up. The controlis generating an
executable G10programand enteringitinto the control’sprogramdirectory.
CREATING TOOL MGMT. FILE -PLEASE WAIT T he tool managementtables are currently beingbacked-up. The controlisgenerating an
executable G10programand enteringitinto the control’sprogramdirectory.
CSSRPML IMIT AUXILIARYSPINDLE2 Theaux spindle 2RPMrequested byCSSisgreaterthanthemaximumCSSRPMlimit. This
limitis setbythesysteminstallerinAMPorcan bereduced by programming aG92 block.
CSSRPML IMIT AUXILIARYSPINDLE3 Theaux spindle 3RPMrequested byCSSisgreaterthanthemaximumCSSRPMlimit. This
limitis setbythesysteminstallerinAMPorcan bereduced by programming aG92 block.
CSS RPMLIMIT FIRST SPINDLE Thespindle1 RPMrequestedbyCSSis greaterthan the maximumCSS RPMlimit. This limitis
setby the systeminstallerin AMP or canbe reduced by programminga G92 block.
CSSRPML IMIT PRIMARYSPINDLE The primary spindle RPMrequestedby CSSis greaterthan the maximumCSS RPMlimit. This
limitisset by the systeminstallerin AMP orcan be reduced byprogramming a G92 block.
CSS RPMLIMIT SECOND SPINDLE The spindle 2RPMrequested by CSS isgreaterthanthemaximumCSSRPMlimit. Thislimitis
setby the systeminstallerin AMP or canbe reduced by programminga G92 block.
CSSRPML IMIT THIRDSPINDLE The spindle 3RPMrequestedby CSS isgreaterthanthemaximumCSSRPM limit. Thislimitis
setby the systeminstallerin AMP or canbe reduced by programminga G92 block.
CURLOOPG/ACLOCKLOST This errorwas generated bya servo amplifier error. Itcanusuallybe corrected byturning off
powerto the amplifier,andthenback on.
CURRENT FEEDBACKERROR The servo module hasdetected faulty ormissing currentfeedbackfrom the digitalservo motor.
The mostlikelycauseofthis errorisbe abrokenor disconnected wire.
CURSORINGNOT ALLOWED While assigning a {CUSTOMTOOL}in{RANDOMTOOL},you cannotcursortoselectanother
tool position.
CUTTER COMP./TTRC INTERFERENCE The cutterradius is too large,reverse motionisrequired,orsomeothercuttercompensation
interferenceexists. Eitheran alternate tooloran alternate tool path mustbe programmed.
Anotheroptionwouldbe to disable cuttercompensationerrordetection.
CYCLE ALREADY ACTIVE An attempt was made tostarta cyclewhileanothercyclewas currently executing.
CYLINDERRADIUSISZERO Thecylinderradiuswas not programmed in avirtual Ccylindrical interpolation(G16.1)cycle.
CYLINDRICALAXISNOT PRESENT Cylindrical interpolationwasprogrammedwithoutatleastone cylindrical interpolationaxes
present (rotary,park,orfeed axes).