Owner manual

Error and System Messages
Appendix B
B-22
Message Description
INVALID PROGRAM NUMBER (P) A programnumbercalled byasub-programor paramacrocall is invalid. A P-wordthatcallsa
sub-programorparamacrocanonly be an all-numericprogramnameas manyas5digitslong.
The O-word precedingthe numericprogram numberin controlmemory cannotbeenteredwith
theP-word.
INVALIDREMOTENODENAME An erroroccurred in G 05 DH+ communicationsblock.
INVALID REMOTE STATION TYPE An erroroccurredinG05 DH+ communicationsblock.
INVALID REPEATCOUNT (L) AnL parameter thatprograms the numberof timesa paramacroorother operationis to be
repeatedwas programmedincorrectlyor outof the legal range. The L-word forrepeatcount
mustbe a whole,positive number. Decimal valuesandnegative values are invalid. The
maximumvalueof an L-wordis9999.
INV ALID ROUGHING CYCLE (P/Q) WORD VALUE When executing a roughing cycle, the startingorending sequence numberof the contour
definingblocks cannotbe found in thecurrently executing program. The sequencenumber of
thecontourblocksis programmed usingthe P and Q words. These blockscanbe anywhere in
theprogram providedthey are residentin thesameprogram,sub-program,orparamacro
programthatcontainsthecalling block.
INVALID SCALEFACTOR(P-WORD) An invalidscalefactorhas been specified. T he P-word hasarangeof 0.0001to999.99999.
INVALID SERVO HARDWARE TYPE The AMPservo parameter thatselectsthe servotype doesnot matchthe hardwarefoundon
thecontrolwhentheAMPfileis downloaded. EitherAMPis misconfiguredor theservo
hardware installed on your system is notcorrectly installed or not of the correct type.
INVALID SHAFT POCKET When entering a customtoolin the randomtool table,an attemptwas madetoassign a shaft
pocketpositionthatisnot in the rangeofthe numberof pocketsassignedtothe tool. The shaft
pocketnumbermustbe equal toorless thanthenumber assignedforthenumberof pockets.
INVALID SHAFT POCKET VALUE Aprogram isattemptingtoenter a custom tool in therandom tooltablewith a invalid shaft
pocketposition(not in therangeof thenumberof pockets assigned tothetool). The shaft
pocketnumbermustbe equal toorless thanthenumber assignedforthenumberof pockets.
The shaftpocketvalue is assignedin a G10.1block followingtheR-word.
INVALID SPCMD VALUE A invalid specialcommanderrortypicallyoccurswhen the servoPROMsarenot compatible
withthe main processorPROMs. Check thesoftware versionnumbers and contact
Allen-Bradleycustomersupportservices.
INVALID SYMBOL NAME An erroroccurredin G05 DH+ communications block.
INVALIDT-CODEFORMAT T his is an invalidT-Code Format
INVALID_T HREAD_ANGLE An attempt was madetoprogramananglethatisoutside theallowable range, whichis0
through120 degrees.
INVALIDTHRESHOLDRATE An invalid thresholdpercentagewas enteredfora tool groupwhilesettingtool management
data. The thresholdpercentagemustrangebetween0 and 100 percent. Only whole positive
numberscan be entered. Ifusing a G10 block,the thresholdpercentageis enteredwitha
Q-word.
INVALID T IMEFORMAT MUST BEHH:MM:SS Aninvalid timeformatwas entered. The timeformatmustbe hour /minute /second
(HH/MM/SS).
INVALIDTOOLAXIS T his is an invalidTool Axis.
INVALID TOOL CUTTER COMPENSATION NUMBER An attempt wasmadeto entera toolradius offsetnumber, forcuttercompensation orTTRC, in
thetool life managementtablethatislargerthan themaximumoffset numberallowed. Ifthe
tablesare being loaded by a G10 program,the radiusoffset isenteredwith a D-wordin the
block.
INVALID TOOL DIAMETER VALUE An invalid tooldiametervaluewas enteredinaprogramblock.
INVALIDTOOLGROUP Anattemptwasmade to create a toolgroupgreaterthan200 in the toolmanagementtables. A
maximumof200 tool groupscanbe used. Ifloading the tablesusing a G10 program,the tool
groupnumberis enteredusing a P-word.