Installation Instruction Manual

BUL. 800Z TOUCH BUTTON AND GUARD INSTALLATION
GP SOLID STATE VERSION
INSTRUCTION SHEET
(ENGLISH)
BROWN
(+) L1
Remove Ring For
30mm Mounting
Not Used
on 22mm Mounting
1 - 4mm (0.04"- 0.16") With Guard
1 - 9.5mm (0.04"- 0.37") Without Guard
Electrical Connections: 10-30V DC
Installation
Specifications (sourcing output)
Touch Button and Guard Installation
(Bulletin 800Z)
1
2
4
3
2
3
1
4
Mini QD (30.5mm)
#889N-F4AE-6F
#889N-F4AE-12F
#889N-F4AE-20F
#889N-R4AE-6F
#889N-R4AE-12F
#889N-R4AE-20F
Micro QD (22.5mm)
#889D-F4AC-2
#889D-F4AC-5
#889D-F4AC-10
WHITE
(1 N.C.)
BLUE
(–) L2
BLACK
(1 N.O.)
BLACK
(1 N.O.)
BROWN
(+) L1
BLUE
(–) L2
WHITE
(1 N.C.)
LOW VOLTAGE–SOLID STATE OUTPUT
Input Voltage: 10-30V DC
Protection: Type 4/4X/13 IP66
1200 psi Washdown
Output Rating: 24 VDC 800 mA
Operation
1. When the power LED is green, the Touch Button is ready for operation.
2. To enable an output, simply place palm or fingers onto ergonomically contoured
surface (see Figure 1).
3. Touch Button output stays activated as long as the sensor surface remains touched.
4. When the output LED is red, the output is de-energized. When the output LED is green,
the output is energized.
Diagnostics
Code 1: The Power/Fault LED (see Figure 2) will turn red for 1 second during power-up. After
the unit self-diagnostics have passed, the Power/Fault LED will turn green and the Output LED
will turn red. If a fault occurs, the Power/Fault LED will remain red.
Code 2: If the device is touched during power-up, the Power/Fault LED will flash red indicating
the device has been disabled. It will continue to flash until power is cycled to the unit.
Code 3: If the unit detects an unacceptable level of noise, it will become disabled and
the red Power/Fault LED will flash until the noise subsides.
Code 4: If conductive films deposit on the sensor surface over time or if a person attempts to
defeat the sensors with foreign objects, the red Power/Fault LED will flash. The fault will disable
the unit and it will remain disabled until the fault is cleared. (fast flash)
Note: In most applications, the grounded neutral line and/or parasitic capacitance between the input
power leads and earth provide(s) sufficient impedance for the device to function properly. If the unit
powers up normally without diagnostic fault codes but does not activate, the power source could be
ungrounded. For additional information, please contact Rockwell Automation Technical Support by
email at [e-mail] or by phone at 440-646-5800.
Figure 1 Figure 2
Sensor Surface
Output LED
Power/Fault LED
CODE TYPE
CODE 2 POWER-UP SAFETY
NOISE DETECTIONCODE 3
DESCRIPTION
MIN. CYCLE TIME
FAULT LED FLASH
SEQUENCE
MARGIN DETECTION
CYCLE POWER REQ.
10 SEC.
1.5 SEC.
CODE 4
• • • • • •
• • • • • • • • •
• • • • • • • • • • • •
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing.
ATTENTION: The 800Z touch button is designed to be an ergonomic replacement for a palm button. It is not a safety
device by itself. This product may cause personal injury or property damage if not installed and used in accordance with
the manufacturer's instructions provided as well as applicable standards and regulations. The user has responsibility to
ensure that all local, state, as well as, national laws, codes and regulations relating to the use and installation of this
device are satisfied.
ATTENTION: This product has undergone a series change from series B to C. Series C product is RoHS compliant.
Agency Certification:
UL, cUL, and CE compliant for all applicable directives.
CE directives include EN 61000-6-2, EN 50081–2,
and EN 60947–5–1. This product is intended for use in an
industrial environment.
Response Time: Off Time Delay: 60 ms (max.)
On Time Delay: 76 ms (max.) 60 ms (avg.)
800Z-GP3
POWER/FAULT OUTPUT
Cat
C
Ser
Guard 800Z-G3AG_
4-Pin Molded Cordsets
800Z-GP3Q64
Mini QD (30.5mm)
22.3mm (0.878") 800Z-GP2_ _
30.5mm (1.200") 800Z-GP3_ _
Maintenance
Unit has no customer serviceable parts.
2.8 Nm (25 LB-IN) 800Z-GP2_ _
3.9 Nm (35 LB-IN) 800Z-GP3_ _
800Z-GP2Q64
Micro QD (22.5mm)
Brown (+)
BLACK (N.O.)
WHITE (N.C.)
800Z-GP_ _ _ _
Sourcing (PNP)
(+)
Load
Load
Blue (–)
(–)
1 SIDE PRINTED,
BODY STOCK WHITE,
BODY INK BLACK
8-1/2" x 11"
4-1/4 x 2-3/4"
PN-54019
FLAT FOLDED
SIZE
MATERIAL
SUPER.
MAT.
NO.
-----
129.3mm
(5.09")
111.9mm
(4.40")
69.8mm
(2.75")
42.3mm
(1.67")
81.6kg (180 lbs) MAX
800Z-G3ALC1
10000071441 01
M. GUELMI 03-17-10
1 1
B
DIR 10000071441 (Version 01)
Printed in U.S.A
PN-54019