Owner manual

ManualsBrandsRockwell Automation ManualsEquipment6189V-MCLPS2 Mounting Clips

Publication 6176M-IN002A-EN-P - August 2006

Installation Instructions

Mounting Clips

Catalog Number 6189V-MCLPS2

About This Publication

This document provides instructions on how to install the mounting clips on

VersaView 6176M light industrial monitors.

Topic Page

Important User Information 2

Environment and Enclosure Information 3

European Union Directive Compliance 3

Before You Begin 4

Installation Guidelines 4

Pre-installation Procedure 5

Install the Mounting Clips 6

Post-installation Procedure 7

Additional Resources 7

Summary of content (8 pages)

PAGE 1
Installation Instructions Mounting Clips Catalog Number 6189V-MCLPS2 Topic Page Important User Information 2 Environment and Enclosure Information 3 European Union Directive Compliance 3 Before You Begin 4 Installation Guidelines 4 Pre-installation Procedure 5 Install the Mounting Clips 6 Post-installation Procedure 7 Additional Resources 7 About This Publication This document provides instructions on how to install the mounting clips on VersaView 6176M light industrial monitors.
PAGE 2
Mounting Clips Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://literature.rockwellautomation.com) describes some important differences between solid state equipment and hard-wired electromechanical devices.
PAGE 3
Mounting Clips 3 Environment and Enclosure Information Review the information on enclosures and environments before installing the product. ATTENTION Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 m (6561 ft) without derating. This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR Publication 11.
PAGE 4
Mounting Clips ATTENTION This product is intended to operate in an industrial or control room environment, which utilizes some form of power isolation from the public low-voltage mains. Some computer configurations may not comply with the EN 61000-3-2 Harmonic Emissions standard as specified by the EMC Directive of the European Union. Obtain permission from the local power authority before connecting any computer configuration that draws more than 75 W of ac power directly from the public mains.
PAGE 5
Mounting Clips 5 • The humidity of the ambient air must not exceed specified limits and must avoid condensation. • In dry environments, static charges build up easily. Proper grounding of the equipment through the ac power cord helps to reduce static discharges, which may cause shocks and damage electronic components. • The enclosure or cover must remain in place at all times during operation.
PAGE 6
Mounting Clips Install the Mounting Clips Mounting clips are required to install the monitors directly into a panel or rack. These are the number of mounting clips required for installation. • For 1550M and 1750M monitors: 10 mounting clips • For the 1950M monitor: 12 mounting clips To install the mounting clips: 1. Slide the mounting clips into the slots on the top, bottom, and sides of the monitor. Mounting Clips for VersaView 1550M and 1750M Monitors Mounting Clips for VersaView 1950M Monitor 2.
PAGE 7
Mounting Clips 7 To remove the mounting clips: 1. Loosen the clip by hand, to remove from the panel. 2. Remove the remaining clips. Post-installation Procedure Perform this post-installation procedure after installing the mounting clips. 1. Make sure the clips are compressed uniformly against the panel. 2. Panel mount or rack mount the monitors. 3. Connect all external cables and the ac power adapter to the monitor. 4. Connect the power cord to the main power supply.
PAGE 8
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://support.rockwellautomation.com, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.