Installation Instructions Industrial Integrated Display Computers with Keypad Catalog Numbers 6180P-12KSXP, 6180P-12BSXP, 6180P-12BPXP, 6180P-12BPXPDC, 6180P-12KPXP, 6180P-15KSXP, 6180P-15BSXP, 6180P-15BPXP, 6180P-15KPXP, 6180P-15BPXPDC Topic Page Important User Information 2 Environment and Enclosure Information 3 European Union Directive Compliance 3 Installation Guidelines 4 Operating Systems 4 Before You Begin 5 Before You Begin 5 Install the Computer 5 Connect Peripherals 10 Connec
Industrial Integrated Display Computers with Keypad Important User Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.rockwellautomation.
Industrial Integrated Display Computers with Keypad 3 Environment and Enclosure Information Review the information on enclosures and environments before installing your computer. ATTENTION: This equipment is intended for use in a Pollution Degree 2 environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 2000 m (6562 ft) without derating. The enclosure door must be closed.
Industrial Integrated Display Computers with Keypad Installation Guidelines Follow these guidelines to make sure your product provides safe and reliable service. • The installation site must have sufficient power. • Make sure that sufficient space is available around air inlets and outlets to provide the circulation necessary for cooling. Never allow air passages to become obstructed. • The ambient air temperature must not exceed the maximum operating temperature.
Industrial Integrated Display Computers with Keypad 5 Before You Begin Before unpacking the product, inspect the shipping carton for damage. If damage is visible, immediately contact the shipper and request assistance. Otherwise, proceed with unpacking. Keep the original packing material in case you need to return the product for repair or transport it to another location. Use both the inner and outer packing cartons to ensure adequate protection for a unit returned for service.
Industrial Integrated Display Computers with Keypad Mounting Clearances Allow adequate space around the computer for mounting, air flow, connections, and maintenance. Sufficient airflow throughout the system unit is required to maintain proper cooling. Clearance should be enough to allow convenient installation or removal of peripheral components, such as the optical disc drive. IMPORTANT Use adequate ventilation or other cooling methods to maintain the product temperature at its specified rating.
Industrial Integrated Display Computers with Keypad 7 Panel Cutout Dimensions The 6180P products must be appropriately mounted in the panel cutout specified below. Model Cut-out Dimensions (HxW), approx. 1200P 279.0 x 450.0 mm (10.98 x 17.72 in.) 1500P 326.4 x 429.3 mm (12.85 x 16.90 in.) Mount the Display Computer in a Panel Mounting clips secure the computer to the panel. The 1200P and 1500P both require 10 mounting clips. Follow these steps to mount the computer in a panel. 1.
Industrial Integrated Display Computers with Keypad 7. Hand-tighten the mounting clips around the bezel by following the tightening sequence shown below. 8. Repeat this process at least three times until the clips are hand-tight and the gasket is compressed uniformly against the panel. 9. Tighten the mounting clips to a torque of 1.4 N•m (12 lb•in) by following the specified torque sequence shown below, being sure to not overtighten.
Industrial Integrated Display Computers with Keypad 9 Product Dimensions Product dimensions for each display computer model are given in mm (in.) 1200P Integrated Display with Keypad 445 [17.5] 427 [16.8] 225 [8.9] 483 [19.0] 311 [12.2] 274 [10.8] 215 [8.5] 1500P Integrated Display with Keypad 427.20 [16.83] 225 [8.9] 483 [19.0] 274 [10.8] 324 [12.8] 355 [14.0] 215 [8.
Industrial Integrated Display Computers with Keypad Connect Peripherals The illustration shows the I/O port panel of the computers. Peripheral components compatible to each port are marked inside the callout figures. The 1200P and 1500P computers have USB ports on both the I/O port side panel and the front access door. You can use these ports to connect various USB devices, such as an external USB HDD or floppy disk drive to the computer.
Industrial Integrated Display Computers with Keypad 11 Connect AC Power A grounded 3-prong inlet IEC320-C14 power cord provides power to the computer. The power supply input accepts 90…264V AC and is autoswitching. Operate the computer in an industrial or control room environment, which uses some form of power isolation from the public low-voltage mains. ATTENTION: Connect the AC power cable to a power source with an earth ground to prevent electrical shock.
Industrial Integrated Display Computers with Keypad To connect DC power, follow these steps. 1. Secure the DC power wires to the terminal block screws. 2. Secure the ground wire to the GND terminal block screw. 3. Apply 24V DC power to the computer. Functional Ground Screw The use of the functional ground screw is not required for safety and regulatory compliance. However, if a supplemental ground is desired, use the functional ground screw on the side panel of the computer.
Industrial Integrated Display Computers with Keypad 13 Connect to the Network The computers have dual Gigabit LAN ports. The computers connect to an Ethernet network, using CAT5 or CAT5E twisted-pair Ethernet cabling with RJ-45 connectors. IMPORTANT To prevent performance degradation of Ethernet communication, do not subject the computer or cables to extreme radiated or conducted high-frequency noise.
Industrial Integrated Display Computers with Keypad The battery life depends on the amount of time the computer is powered on. The table lists the estimated life span of the battery. If the computer does not display the correct time and date, replace the battery. On-time Expected Battery Life 0 hours/week 4 years 40 hours/week 5.5 years 80 hours/week 7 years ATTENTION: A risk of fire and chemical burn exists if the battery is not handled properly.
Industrial Integrated Display Computers with Keypad 15 b. Remove the old battery from its socket. 6. Insert the new battery with the positive polarity (+ side) facing up, and make sure that it is seated completely. 7. Observe the post-configuration procedure. a. Make sure that all components are installed according to the described step-by-step instructions. b. Make sure that no loose tools or parts are left inside the computer. c.
Industrial Integrated Display Computers with Keypad Backlight Assembly Disposal ATTENTION: The backlight assembly in this unit contains mercury. At the end of its life, this equipment should be collected separately from any unsorted municipal waste. Transport the Product If you need to ship your computer via common carrier or otherwise transport it to another location, you must first uninstall the unit from the panel and place it in its original packing material.
Industrial Integrated Display Computers with Keypad 17 Specifications Hardware and Electrical Specifications Attributes 6180P-12 and 6180P-15 Models Display Display type Color Active Matrix TFT Touch screen, optional Resistive antiglare Display size, diagonal 1200P 1500P 308 mm (12.1 in.) 381 mm (15.0 in.) Display area (WxH), approx 1200P 1500P 246 x 185 mm (9.7 x 7.3 in.) 305 x 229 mm (12 x 9 in.
Industrial Integrated Display Computers with Keypad Environmental Specifications Attribute 6180P-12 and 6180P-15 Models Temperature, operating 0…55 °C (32…131 °F) Temperature, storage -20…60 °C (-4…140 °F) (1) 20…85% without condensation Relative humidity, operating (2) Relative humidity, nonoperating 5…90% without condensation Vibration, operating 0.006 in. p-p, (10…57 Hz); 1 g (57…640 Hz) Vibration, nonoperating 0.012 in.
Industrial Integrated Display Computers with Keypad 19 Additional Resources For additional information about the 6180P Integrated Display Computers with Keypad, refer to the following publications. Resource Description 6180P Integrated Display Computer with Keypad user manual, publication number 6180P-UM001 Overview of the system and description of procedures for installation, connections, configuration, and troubleshooting.
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://www.rockwellautomation.com/support, you can find technical manuals, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. You can also visit our Knowledgebase at http://www.rockwellautomation.
