User Manual

ManualsBrandsRockwell Automation ManualsEquipment42KL MiniSight

Installation Instructions

MiniSightt Photoelectric Sensors

AC/DC Sensors

Retroreflective Diffuse

Wide Angle

Diffuse

Polarized

Retroreflective

Large Aperture

Fiber Optic

Small Aperture

Fiber Optic

Visible Red Fixed Focus

Transmitted Beam

Receiver Source

1 Catalog Number 4 2 K L -- U 2 T C -- X X 42KL--D1TC--XX 4 2 K L -- W 1 T C -- X X 42KL--P2TC--XX 42KL--G1TC--XX 42KL--L2TC--XX 42KL--F2TCS--XX 42KL--F2TCL--XX

42KL--RTCV--XX

42KL--RTC--XX 42KL--E1QZB--XX

2 Sensing Distance 5m (16.4ft) 380mm (15in) 180mm (7in) 2m (6.6ft) Depends on Fiber Depends on Fiber 16mm (0.63in) 43mm (1.7in) 4m (13ft) 30m (98ft)

3 Outputs Two Wire Light/Dark Selectable —

4 Supply Voltage 21.6--250V AC/DC

5 Load Current 100mA max —

6 Leakage Current 1.7mA rms max —

7 Power Consumption 4VA max

8 Response Time 8.3ms 16.6ms max

9 Approvals UL recognized, CSA, CE marked for all applicable directives

10 Protections Short Circuit, Reverse Polarity, False Pulse

11 Indicators Green = Power Yellow = Output Orange = 2.5X Margin, Flashing for Short Circuit Protection

12 Field of View

1.5_ 5_ 18_ 1.5_

Depends on Fiber Depends on Fiber — —

13 Transmitting LED Visible Red 660nm Infrared 880nm Visible Red 660nm Infrared 880nm Visible Red 660nm — Infrared 880nm

14 Sensitivity Adjustment Yes: 11 turn, clutch protected —

15 Operating T emperature -- 4Fto+158F(--20Cto+70C)

16 Housing—Cover—Lens Material Noryl N190—Radel R5000—Acrylic

17 Operating Environment NEMA 4X, 6P, IP67, withstands 8270kPa (1200 psi) washdown

Catalog Number Key—XX could equal

A2 = 2m, 300V cable F4 = pigtail w/4-pin DC micro QD G3 = pigtail w/3-pin AC micro QD Y4 = pigtail w/4-pin DC pico QD X4 =custom 4-pin connector

Not all variations available. Contact factory for availability.

DC Sensors

Retroreflective Diffuse

Wide Angle

Diffuse

Polarized

Retroreflective

Large Aperture

Fiber Optic

Small Aperture

Fiber Optic

Visible Red Fixed Focus

Visible Green

Fixed Focus

Transmitted Beam

Receiver Source

1 Catalog Number 42KL--U2LB--XX 42KL--D1LB--XX 42KL--W1LB-- XX 42KL--P2LB --XX 42KL--G1LB--XX 42KL--L2LB--XX 42KL--F2LBS--XX 42KL--F2LBL--XX 42KL--F3LBS--XX

42KL--RLBV --XX

42KL--RLB--XX 42KL--E1EZB--XX

2 Sensing Distance 5m (16.4ft) 380mm (15in) 180mm (7in) 2m (6.6ft) Depends on Fiber Depends on Fiber 16mm (0.63in) 43mm (1.7in) 16mm (0.63in) 4m (13ft) 30m (98ft)

3 Outputs NPN/PNP Light/Dark Selectable —

4 Supply Voltage 10.8--30V DC

5 Load Current 100mA max —

6 Leakage Current 0.1mA max —

7 Power Consumption 1.5W max

8 Response Time 1ms max 15ms max

9 Approvals UL, CSA, CE marked for all applicable directives

10 Protections Short Circuit, Reverse Polarity, False Pulse

11 Indicators Green = Power Yellow = Output Orange = 2.5X Margin, Flashing for Short Circuit Protection Green = Power

12 Field of View

1.5_ 5_ 18_ 1.5_

Depends on Fiber Depends on Fiber — — —

13 Transmitting LED Visible Red 660nm Infrared 880nm Visible Red 660nm Infrared 880nm Vi sible Red 660nm Visible Green

525nm

— Infrared 880nm

14 Sensitivity Adjustment Yes: 5 turn, clutch protected —

15 Operating Temperature -- 4Fto+158F(--20Cto+70C)

16 Housing—Cover—Lens Material Noryl N190—Radel R5000—Acrylic

17 Operating Environment NEMA 4X, 6P, IP67, withstands 8270kPa (1200 psi) washdown

Catalog Number Key—XX could equal

A2 = 2m, 300V cable F4 = pigtail w/4-pin DC micro QD G3 = pigtail w/3-pin AC micro QD Y4 = pigtail w/4-pin DC pico QD X4 =custom 4-pin connector

Not all variations available. Contact factory for availability.

 When using the transmitted beam sensing mode in high noise (EMF) applications, it is recommended that the 42KL--RxxV receiver be used whenever possible. This will prevent the sensor from “locking on” due to high line voltage

spikes.

Summary of content (6 pages)

PAGE 1
Installation Instructions MiniSightt Photoelectric Sensors AC/DC Sensors Retroreflective Diffuse Wide Angle Diffuse Polarized Retroreflective Large Aperture Fiber Optic Small Aperture Fiber Optic Transmitted Beam Visible Red Fixed Focus Receiver 1 Catalog Number 42KL-- U2TC-- XX 42KL--D1TC-- XX 42KL-- W1TC-- XX 42KL-- P2TC-- XX 42KL-- G1TC--XX 42KL--L2TC-- XX 42KL-- F2TCS-- XX 42KL-- F2TCL--XX 42KL-- RTCV-- XX 2 Sensing Distance 5m (16.4ft) 380mm (15in) 180mm (7in) 2m (6.
PAGE 2
High Speed DC Sensors Retroreflective Diffuse Wide Angle Diffuse Polarized Retroreflective Large Aperture Fiber Optic Small Aperture Fiber Optic Visible Red Fixed Focus Receiver 42KL--RLBQ--XX 1 Catalog Number 42KL--U2LBQ-- XX 42KL-- D1LBQ--XX 42KL-- W1LBQ--XX 42KL-- P2LBQ--XX 42KL--G1LBQ-- XX 42KL--L2LBQ-- XX 42KL--F2LBSQ--XX F2LBLQ-- XX 42KL--F3LBSQ--XX 2 Sensing Distance 2.5m (8.2ft) 190mm (7.5in) 90mm (3.5in) 1m (3.3ft) Depends on Fiber Depends on Fiber 16mm (0.
PAGE 3
Italiano Español Portuguêas Operating Distance Selection The maximum operating distance is based on installing the sensor in a relatively clean environment. Normal industrial environments actually range from moderately dusty to extremely dirty. Greater operating margin may be required which can be obtained by reducing the operating distance of the control. English Wahl der Reichweite Die maximale Reichweite basiert auf einer Installation des sensors in einer relativ sau-beren Umgebung.
PAGE 4
Sensor Wiring Diagrams 11--30V DC Sensors NPN/PNP Brown White Load Black Load + -- Blue 1 2 Brown White 4 Black 3 + Load Load Micro Transmitted Beam Source Pico 1 4 2 4 2 3 1 1 T Brown + Blue -- 4 Micro 2 -- Blue 3 -- Blue + Brown T 3 Pico 1 4 2 4 2 3 1 3 Cable Cable 22--250V AC/DC Sensors DC Wiring AC Wiring Brown Blue L1 Load L2 Cable 2 ~ ~ Red/Black 1 Green 3 Red/White L1 Load L2 ~ Brown 3 1 ~ + 2 -- Blue 2 Red/Black 1 Green 3
PAGE 5
Sensor Dimensions—mm (inches) (continued) Large Aperture Fiber Optic Sensors Fiber Retaining Clip 18 (0.71) Dia. M18 x 1mm thread Fiber Retaining Clip (supplied with sensor) Grooved Fiber Optic End Tip Catalog number 75012--097 max torque = 10in/lbs 20.5 (0.80) 16.6 (0.65) NOTE: MiniSightt large aperture fiber optic sensors require Series “C” Glass Fiber Optic cables with grooved control end tips. 25.3 (0.99) Small Aperture Fiber Optic Sensors 16.3 (0.
PAGE 6
Accessories—mm (inches) (continued) Straight Mounting Bracket #60--2656 Apertures Quick-Disconnect Cordsets Snap-on apertures for Transmitted Beam applications are available for MiniSight sensors to detect small objects. Select an aperture slot size that will be blocked by the object being detected for best results. An aperture should be placed on both the source and receiver units for proper operation. 1mm slotted aperture, Qty. 20: #60--2673 2mm slotted aperture, Qty.