Installation Instructions Manual

ManualsBrandsRockwell Automation ManualsEquipment4100-IF2 IF2 I/O Interface to PDM

Publication 4100-IN001A-EN-P- February 2001

Installation Instructions

IF2 I/O Interface to PDM

(Catalog Number 4100-IF2)

The IF2 I/O Interface to PDM is a printed circuit board intended for

use with the positioning drive modules (PDM). The purpose of this

board is to reverse the polarity of the I/O circuit to remove the

problem of compatibility that may arise from connecting any

external control conductors to the I/O.

See page:

Important User Information 2

Allen-Bradley Support 3

Compliance to the European Union Directive 4

Low Voltage Directive 4

Preventing Electrostatic Discharge 5

Overview 6

Installation 7

Mounting 7

Wiring 8

Wiring Cable Flying Leads to the Plugs 8

Wiring the P1 Connector 10

Wiring Diagram 10

Wiring the P2 User Connector 11

Cables 11

Summary of content (12 pages)

PAGE 1
Installation Instructions IF2 I/O Interface to PDM (Catalog Number 4100-IF2) The IF2 I/O Interface to PDM is a printed circuit board intended for use with the positioning drive modules (PDM). The purpose of this board is to reverse the polarity of the I/O circuit to remove the problem of compatibility that may arise from connecting any external control conductors to the I/O. .
PAGE 2
IF2 I/O Interface to PDM Important User Information Those responsible for the application and use of this product must satisfy themselves that all necessary steps have been taken to assure that the application and use of this product meets all performance and safety requirements, including all applicable laws, regulation codes, and standards. The illustrations, charts, sample programs, and layout examples shown in this manual are intended solely for purposes of example.
PAGE 3
IF2 I/O Interface to PDM 3 Allen-Bradley Support Allen-Bradley offers support services worldwide, with over 75 Sales/ Support Offices, 512 authorized Distributors and 260 authorized Systems Integrators located throughout the United States alone, plus Allen-Bradley representatives in every major country in the world.
PAGE 4
IF2 I/O Interface to PDM Compliance to the European Union Directive This product doesn’t bear the CE mark because it has been defined as a component. It has been tested as part of a system and is included in the declaration of conformance for the system It has been designed and tested to meet the following directives.
PAGE 5
IF2 I/O Interface to PDM 5 For specific information required by EN 60204, see the appropriate sections in this publication, as well as the following Allen-Bradley publications: • Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 • Automation Systems Catalog, publication B111 This equipment is classified as open equipment and must be installed (mounted) in an enclosure during operation as a means of reducing user exposure to hazards.
PAGE 6
IF2 I/O Interface to PDM Overview The IF2 I/O Interface to PDM is a printed circuit board intended for use with the positioning drive modules (PDM). Figure 1 Front View of I/O Interface Board These drives are built with output stages which source current to their loads, and input stages which require a current sinking input to operate.
PAGE 7
IF2 I/O Interface to PDM 7 Installation The interface is a DIN rail mounting unit which has a terminal strip (1.5 mm2 screw clamp type) down each side. Mounting The Interface board has 2 mounting feet on the back to attach it to the DIN rail.
PAGE 8
IF2 I/O Interface to PDM Wiring The flying leads from the PDM drive is wired to the IF2 I/O Interface to PDM board using the connector marked P1. The flying leads from the external controller are wired to the connector marked P2 User. Each set of connectors have 26 slots available and the wiring is a 1 to 1 set up. The IF2 I/O Interface should be mounted as close as possible to the associated PDM. The wires from the PDM to the IF2 should be in the same railway and should not contain any power leads.
PAGE 9
IF2 I/O Interface to PDM If the terminals are: Do this: Open Go to step 4 9 3. Using a small, flat-head screwdriver, turn the clamping screw counter-clockwise several times. 4. Using a proper stripping tool, strip the wire insulation back on the cable lead. IMPORTANT All terminals accommodate a maximum of 14 gauge wire. 5. Trim the cable lead so that 0.275 inches of metal wire is exposed. 6. Insert the cable lead in the appropriate terminal. Refer to the proper figures for their locations. 7.
PAGE 10
IF2 I/O Interface to PDM 10 Wiring the P1 Connector The PDM side is designed to connect directly on a 1 for 1 basis to the I/O connectors on the PDM drive, as shown in the following diagram. Figure 4 Wiring Diagram.
PAGE 11
IF2 I/O Interface to PDM 11 Conductor size must not be greater than 1.5 mm2. The I/O circuits in the PDM drive are protected by a 1 amp fuse contained in the drive. Wiring the P2 Connector The P2 User I/O requires a separate clean 24 volt nominal DC supply. There is no galvanic connection from one side to the other, and the user 24 volt supply must be grounded on the negative side to the protective earth system.